İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Cross-Hole Countersinks: A Slanting Hole Through the Cone Makes One Spiral Shearing Lip (Taylor, 1903)
Forge

Oluşturan

Forge

13. Kasım 2026NO
10
0
0
0
0

Cross-Hole Countersinks: A Slanting Hole Through the Cone Makes One Spiral Shearing Lip (Taylor, 1903)

John M. Taylor of Hartford, Connecticut, received US 724,520, dated 7 April 1903, for a countersink that shears wood smoothly. Its conical head has a hole drilled through it at a slant that crosses the axis and reaches the point. One edge of that hole is the cutting lip, a spiral curve from the point out to the rim, and the chips go straight out through the hole to the back. A short band behind the cone guides it. We turn a set of three from tool steel and harden them. The patent gives no sizes; every size here is ours.
Orta
About 1 day

Talimatlar

1

Where the slanting hole must go

Jupyter defteri yükleniyor…
2

Read US 724,520

"One of the outer edges of the wall of the opening forms a cutting-lip 8, which is of spiral formation, whereby it is effective to make a shear cut, and terminates in a shoulder 9, forming an entering or cutting point 4 at the apex of the conical head 2."
3

Turn the blanks

From octagonal tool steel big enough for each head, turn three blanks: a 90 degree cone 2 to a sharp point, 12, 16 and 20 mm across at its base; a band 5 2 mm long at that diameter as the guide; a truncated cone 6 down to an 8 mm shank 50 mm long. File three flats on each shank's end for the chuck. Heat each to a cherry red and let it cool slowly in the air, to soften it for drilling.

Bu adım için malzemeler:

Sekizgen takım çeliği çubukSekizgen takım çeliği çubuk2 adet

Gerekli aletler:

Metal Torna TezgâhıMetal Torna Tezgâhı
3 ayaklı torna aynası3 ayaklı torna aynası
Torna kesici kalemiTorna kesici kalemi
Kesme kalemiKesme kalemi
İletkiİletki
Dijital Kumpas 6 İnçDijital Kumpas 6 İnç
Eğe TakımıEğe Takımı
Demirci OcağıDemirci Ocağı
Demirci MaşasıDemirci Maşası
Koruyucu gözlükKoruyucu gözlük
4

Drill the slanting opening 7

Hold a blank in the machine vice tilted so the drill meets the cone's side at 35 degrees to the tool's axis, aimed to cross the axis just behind the point (the notebook gives how far). Drill through with a drill 0.45 of the head across: 5.5, 7 and 9 mm, so the hole breaks out through the point on one side and out of the back cone on the other. Open the back of the hole a little larger, so it tapers towards the shank.

Gerekli aletler:

Sütunlu MatkapSütunlu Matkap
Makine MengenesiMakine Mengenesi
İletkiİletki
Matkap Ucu TakımıMatkap Ucu Takımı
Dijital Kumpas 6 İnçDijital Kumpas 6 İnç
5

File the lip 8

With a round needle file, clean the hole's edge on the side that leads as the countersink turns, leaving it sharp from the point to the band: that is the spiral cutting lip. File a little relief on the cone just behind it, and leave the shoulder 9 at the point.

Gerekli aletler:

İğne Eğe Takımıİğne Eğe Takımı
Makine MengenesiMakine Mengenesi
Taşlama motoruTaşlama motoru
6

Harden and temper

Heat each head to a cherry red, until a magnet no longer sticks, and quench it point first in water, moving it about. Rub it bright with a stone, heat the shank gently 20 mm behind the head, and quench again as soon as a light straw colour reaches the cutting lip.

Gerekli aletler:

Demirci OcağıDemirci Ocağı
Demirci MaşasıDemirci Maşası
Küçük MıknatısKüçük Mıknatıs
Su verme kovasıSu verme kovası
SuSu
Bileği TaşıBileği Taşı
Kaynak eldivenleriKaynak eldivenleri
Koruyucu gözlükKoruyucu gözlük
7

Hone and test

Hone the lip lightly with the stone. Drill a few screw holes in hardwood and countersink them in the drill: the cone should cut a smooth bell without chatter and the chips should come out of the hole at the back.

Gerekli aletler:

Bileği TaşıBileği Taşı
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Sert Ağaç TahtasıSert Ağaç Tahtası
Koruyucu gözlükKoruyucu gözlük
8

Troubleshooting

Countersink troubleshooting.

Flow

Loading...
9

History and honest limits

**John M. Taylor** of Hartford, Connecticut, US 724,520, dated 7 April 1903, filed 7 November 1901. He claimed "a countersink having a cone-shaped head provided with an opening crossing diagonally to the axis within the length of the tool and intersecting the apex of the cone, said opening having a curved edge forming a cutting-lip", and a two-part shank for brace or chuck. We make one-piece shanks for a chuck. He gives no sizes, angle or steel; our 90 degree cones, sizes and the house hardening are ours.

Malzemeler

1

Gerekli Aletler

22

İlgili Blueprint'ler

Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...