SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

The Cam-Lever Lemon Squeezer: A Cam on a Shaft Presses the Plunger, Springs Lift It
A plunger pressed straight down by the hand needs a strong push to empty a lemon.
A. Clarence Weeks of New York received US 165,638, dated 13 July 1875, for a squeezer with a frame on legs over a dish, a perforated bowl in the frame, a plate hinged to one end carrying the plunger, two standards on the frame with a shaft across them carrying "a cam-lever, G, arranged for contact of its face or bearing-surface with the upper side of the board or plate, which carries the plunger", and springs from the plate to the standards. "By the use of the cam-lever an immense power is obtained, and the juice is extracted from the lemon in a more thorough and perfect manner than when the power is applied directly to the plate or bar carrying the plunger."
This rung works out the cam's average force, with a work check, then builds the frame, the hinged plate and the cam lever in hardwood and steel, and squeezes lemons with it.
Orta
About 5 hours
Talimatlar
1
1
The cam's force
The cam's force
Jupyter defteri yükleniyor…
2
2
A lever press before it
A lever press before it
The embedded blueprint presses the lemon with the lever itself. Weeks puts a cam lever over a hinged plate, so a turn of the lever gives a far greater push.
3
3
Read US 165,638
Read US 165,638
"Two standards, E E, are attached to the frame A, one on each side, in the upper portions of which standards are bearings for a shaft, f, to which is attached, midway of its length, a cam-lever, G, arranged for contact of its face or bearing-surface with the upper side of the board or plate, which carries the plunger. J is a spring, which may be of rubber or metal, having its lower end attached to the board or plate C, and its upper end attached to the standard E."
"When the cam-lever G is depressed its face or bearing-surface presses upon the board or plate C, and forces the plunger into the bowl upon the lemon."
4
4
Build the squeezer and press lemons
Build the squeezer and press lemons
**Frame and bowl.** Make a hardwood board frame on four legs, tall enough for a dish beneath, with a hole in it. Fit a tin-can bowl with a punched base into the hole.
**Plate and plunger.** Hinge a hardwood plate to one end of the frame with a butt hinge, and screw a hardwood plunger to its underside so it enters the bowl.
**Standards and cam.** Screw two hardwood standards to the frame's sides beside the plate and run a steel rod across between them as the shaft f. Cut a hardwood cam lever with a curved face whose distance from the shaft grows by about 15 mm over 60° of turn, drill it for the shaft, and fix it in the middle of the rod with a pin.
**Springs.** Hook two extension springs from the plate to the standards so they lift the plate when the cam is raised.
**Test.** Put a half lemon in the bowl over a dish and press the lever down. Compare the juice with a half pressed by pushing the plate down by hand.
Bu adım için malzemeler:
Sert Ağaç Tahtası2 adet
Sert Ahşap Blok2 adet
Ahşap kavela0.6 metre
Ahşap vidalar16 adet
Ahşap Tutkalı1 adet
Teneke kutu1 adet
Kapı menteşesi1 adet
Yumuşak Çelik Çubuk0.2 metre
Çiviler2 adet
Çekme yayı2 adet
Limon3 adetGerekli aletler:
El Testeresi
Ahşap oluk kalemi takımı
Törpü
Kablosuz Matkap
Matkap Ucu Takımı
Sac makası
Çekiç
Tornavida takımı
Demir Testeresi
Mutfak bıçağı
Dijital Mutfak Terazisi
Deri İş Eldiveni5
5
A cam that slips, jams or does not lift
A cam that slips, jams or does not lift
Cam-lever lemon squeezer troubleshooting.
Flow
Loading...
6
6
History and honest limits
History and honest limits
**A. Clarence Weeks** of New York, New York, filed US 165,638 on 26 April 1875; it is dated 13 July 1875. His frame A had feet or legs a, the bowl B had perforations b, the plate C was hinged to one end of the frame, and there could be one spring or two. His claim is the frame with the perforated bowl and standards, the pivoted plate with its plunger, the springs, and the shaft with its cam lever.
**Honest limits.** Hardwood, a tin bowl and a steel rod stand in for his parts. The notebook gives the average force without friction; its forces, lengths and angles are examples. Your juice is the result.
Malzemeler
11- 2 adetYer Tutucu
- 2 adetYer Tutucu
- 0.6 metreYer Tutucu
- 16 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 0.2 metreYer Tutucu
- 2 adetYer Tutucu
- 2 adetYer Tutucu
- 3 adetYer Tutucu
Gerekli Aletler
12- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

The Ring-Set Lemon Squeezer: A Bowl Held in Its Handle by a Screwed Ring
YourGrandma tarafından
Ağaç işleri
21
0
0
0
0
0

The False-Bottom Lemon Press: A Hinged Lever Over a Die, and One Hole for the Juice
TheChef tarafından
Ağaç işleri
15
0
0
0
0
0

The Clamp-Frame Lemon Squeezer: A Screw Press That Clamps to the Table
Forge tarafından
Metal işleme
11
0
0
0
0
0
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.