SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
The Savonius Rotor: Two Hollow Vanes, Any Wind, Always Starts
Volt

Oluşturan

Volt

27. Eylül 2026SE
10
0
0
0
0

The Savonius Rotor: Two Hollow Vanes, Any Wind, Always Starts

Cut a cylinder in half lengthwise, slide the halves apart so they overlap, and stand them on a vertical shaft: that is the rotor Sigurd Savonius of Finland patented in 1924–29. The wind pushes harder on the hollow of one vane than on the back of the other, and air flowing through the overlap from one hollow into the other helps it along. It turns in wind from any direction without steering, starts itself in the lightest breeze, and gives strong torque at low speed — for pumping water, ventilating, or driving a current meter. It is also slow and inefficient, because it is pushed by drag. This rung works out the drag machine's ceiling and builds a Savonius rotor from a PVC pipe, measuring its torque with a string brake.
Başlangıç
About 4 hours

Talimatlar

1

Read Savonius's overlap

US 1,697,574, 'Rotor Adapted to be Driven by Wind or Flowing Water', Sigurd J. Savonius. The vanes are *"hollow-shaped"* and *"overlapping"*, so that the space between them forms an air passage *"from the hollow side of the vane d, to the hollow side of the other vane c"*. His text compares it with the rotating cylinder then being studied at the Aerodynamische Versuchsanstalt in Göttingen, which it cites. The overlap is the detail that separates a Savonius rotor from two cups on a stick.
2

The drag machine's ceiling

Jupyter defteri yükleniyor…
3

Build it from a PVC pipe

Cut a 300 mm length of 110 mm PVC pipe in half lengthwise with a saw. Cut two plywood end discs 240 mm across. Screw the two half-pipes between the discs, hollow faces opposite, each shifted towards the centre so they **overlap by about a fifth of a half-pipe's width**, leaving the air passage Savonius describes. Run a threaded-rod shaft through the centre of both discs, held by nuts, and carry it vertically in two skateboard bearings in a plywood frame.

Bu adım için malzemeler:

PVC BoruPVC Boru1 adet
Kontrplak levhaKontrplak levha1 yaprak
Dişli milDişli mil1 adet
Kaykay rulmanlarıKaykay rulmanları2 adet
Makine vidalarıMakine vidaları12 adet

Gerekli aletler:

Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Kurbağacık anahtarKurbağacık anahtar
CetvelCetvel
Boru kesiciBoru kesici
4

Measure torque with a string brake

Wrap fishing line once round the shaft. Tie one end to the spring scale fixed to the frame, and hang a small weight on the other end, so the line rubs on the turning shaft as a brake. The braking torque is **(weight − scale reading) × shaft radius**. Put the rotor in front of the box fan. Start with a light weight: the rotor spins fast. Add weight step by step, reading the speed with the tachometer and the scale each time, until it stalls. Power = torque × angular speed. Turn the rotor to face the wind at a different angle: it does not care. Start the fan at its lowest setting with the rotor stopped: it starts by itself. Those two facts are why Savonius rotors exist.

Bu adım için malzemeler:

Misina (tek katlı)Misina (tek katlı)1 rulo
AğırlıkAğırlık1 takım

Gerekli aletler:

Kutu vantilatör (ayarlı hız)Kutu vantilatör (ayarlı hız)
El anemometresiEl anemometresi
Dijital TakometreDijital Takometre
Kuvvet Ölçer (Yaylı Terazi)Kuvvet Ölçer (Yaylı Terazi)
Dijital Kumpas 6 İnçDijital Kumpas 6 İnç
5

History and context

**US 1,697,574, 'Rotor Adapted to be Driven by Wind or Flowing Water', Sigurd J. Savonius; filed 13 August 1925 (Serial 49,985), claiming a Finnish filing of 12 December 1924; granted 1 January 1929.** The title names water as well as wind: the same rotor turns in a current. **Honest limits.** Low efficiency — a drag machine cannot beat the notebook's ceiling by much. Heavy for its power, because the whole swept area is solid vane. Its torque pulses twice per turn, which is why many are built as two stages twisted 90° apart, or with helical vanes.

Malzemeler

7

Gerekli Aletler

10

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...