SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

The Sheet-of-Water Fountain Brush: Tapered Slots Part the Bristles
Water dribbled onto the back of a brush stays in the bristles and never reaches the surface being washed.
Frank L. Brinn of Milwaukee received US 840,604, patented 8 January 1907, for a fountain brush in which "the fluid may be delivered to the longitudinal central portion of the brush in a sheet, which when the fluid is turned on at full head will serve to separate the bristles and flush the surface to be washed": slots through the block narrow toward the bristles, fed from a cylinder on top through a tubular handle, with a cup on the handle to catch what runs down.
This rung works out how the taper speeds the sheet, then cuts the slots in a scrub brush, plumbs it and compares full flow with throttled flow.
Orta
About 4 hours
Talimatlar
1
1
Sheet speed from the slot
Sheet speed from the slot
Jupyter defteri yükleniyor…
2
2
Water through a brush's back before it
Water through a brush's back before it
The embedded blueprint jets or soaks water through openings in a brush's back. Brinn shapes the openings into tapered slots so the water leaves as a sheet.
3
3
Read US 840,604
Read US 840,604
"By opening the valve at 3 to its full capacity a sheet of water will be discharged which will separate the bristles and effectively flush the surface to be washed, whether the bristles are in contact with such surface or not. By partially closing the valve at 3 the sheets of water escaping through the openings 18 are broken up by the bristles, and the water thus becomes distributed throughout the brush."
4
4
Cut the slots
Cut the slots
On the scrub brush's top mark two slots 60 × 8 mm, 90 mm apart on the centre line. Drill a row of holes in each and cut it through with the coping saw.
Bu adım için malzemeler:
Fırça (sert kıllı)1 adetGerekli aletler:
Tezgah Mengenesi
Kablosuz Matkap
Matkap Ucu Takımı
Kıl Testere
Silinmez Kalem
Cetvel5
5
Taper the slots
Taper the slots
Pare each slot with chisels so its long sides close to about 1.5 mm at the bristle face and its ends open out to 70 mm. Trim the bristles along the slot line.
Gerekli aletler:
Ahşap oluk kalemi takımı
Çekiç
Dijital Kumpas 6 İnç
Maket Bıçağı6
6
Make the manifold
Make the manifold
Cut 160 mm of 22 mm copper tube and cap both ends with fittings. File a 4 mm slot along its underside over both brush slots. Fit a tee in its middle for the handle.
Bu adım için malzemeler:
Bakır boru1 adet
Pirinç bağlantı parçaları1 adetGerekli aletler:
Boru kesici
Eğeler (El Eğesi)
Kurbağacık anahtar7
7
Seat the manifold
Seat the manifold
Bed the manifold on the brush in silicone over a rubber gasket and strap it down with an aluminium strip and four wood screws.
Bu adım için malzemeler:
Kauçuk levha1 adet
Alüminyum sac1 adet
#8 x 1" ahşap vidası1 adetGerekli aletler:
Sac makası
Tornavida takımı
Maket Bıçağı8
8
Handle, valve and drip cup
Handle, valve and drip cup
Fit 1.2 m of 15 mm copper tube to the tee, with a ball valve and hose connector at its top. Slide a small tin can, holed and sealed with silicone, onto the handle as a drip cup, and fit a short copper spout low on its side.
Bu adım için malzemeler:
Bakır boru1 adet
Küresel vana1 adet
Pirinç bağlantı parçaları1 adet
PTFE diş sızdırmazlık bandı1 adet
Teneke kutu1 adetGerekli aletler:
Boru kesici
Kurbağacık anahtar
Kablosuz Matkap
Matkap Ucu Takımı9
9
The patent drawing
The patent drawing
US 840,604 drawing sheet, public domain (expired patent).

10
10
Full flow against throttled
Full flow against throttled
Connect the garden hose. With the valve fully open, hold the brush 2 cm off a board and watch the sheet part the bristles; then close it half and watch the water spread through them. Time a litre into the jug each way.

Bu adım için malzemeler:
Bahçe hortumu1 adet
Su1 adetGerekli aletler:
Ölçü sürahisi
Kronometre
Cetvel11
11
A sheet that sprays, sputters or leaks
A sheet that sprays, sputters or leaks
Sheet-of-water fountain brush troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
**Frank L. Brinn**, a citizen of Canada residing in Milwaukee, filed US 840,604 on 20 February 1905; it was patented 8 January 1907. His cylinder is held to the block by a plate with packing and screws, its slots feeding the slot-apertures; the handle's end carries a rubber sheath and the valve; the cup, with its spout, collects the water instead of letting it run down the handle when the brush is raised.
**Honest limits.** A slotted copper tube stands in for his cylinder, and a tin can for his cup. The notebook treats the sheet as uniform. What you see on the board is the result.
Malzemeler
12- 1 adetYer Tutucu
- 1 adetYer Tutucu
- Yer Tutucu
- 2 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- Yer Tutucu
- 1 adetYer Tutucu
- Bahçe hortumu%10 komisyon1 adetYer Tutucu
- 1 adetYer Tutucu
Gerekli Aletler
17- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

The Tube-in-the-Back Fountain Brush: Turn the Tube and the Jets Become a Soak
YourGrandma tarafından
Mekanik
17
0
0
0
0
0

The Long-Handled Fountain Brush: A Ring of Holes Wets the Bristles From the Ground
Martin tarafından
Mekanik
8
0
0
0
0
0

The Hose and Its Clip: Why It Was Tight When You Fitted It
Martin tarafından
Aletler
21
0
0
0
0
0
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.