İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Thimble: the Pitted Iron Thimble Gilt Inside (Rouy and Berthier, Ure 1839)
Forge

Oluşturan

Forge

4. Kasım 2026NO
13
0
0
0
0

Thimble: the Pitted Iron Thimble Gilt Inside (Rouy and Berthier, Ure 1839)

The Paris method of Rouy and Berthier: thin sheet-iron discs, red-hot, punched step by step into a cup through five ever-deeper hollows, then turned, pitted and annealed on the lathe, gilt inside with gold leaf pressed on by a steel mandril, and banded outside with a gold fillet. Variable: closed (pitted round end) or open (no end, for tailors). Source: Andrew Ure, Dictionary of Arts, Manufactures and Mines (1839), 'Thimble'. Picture: a modern pitted thimble (Commons, CC BY-SA 3.0).
İleri
Unknown

Talimatlar

1

Punch the blanks

Cut sheet iron 1/24 in thick into strips sized for the thimbles. Run them under a punch press to cut discs about 2 in across, left joined by a tail, a dozen to a strip.

Bu adım için malzemeler:

Demir levha (dövülmüş)Demir levha (dövülmüş)1 1/24 in

Gerekli aletler:

Zımba presiZımba presi
2

Sink the cup

Heat the blanks red-hot and lay each on a mandril fitted to its size. Strike the middle with a round-faced punch about as thick as a finger to sink it into the first hollow, then drive it through a block with five hollows of increasing depth until it has the thimble's shape.

Gerekli aletler:

Demirci OcağıDemirci Ocağı
MaşaMaşa
Bilinmeyen metalBilinmeyen metal
ÇekiçÇekiç
3

Turn and pit on the lathe

Chuck the rough thimble in the lathe, polish the inside, turn the outside, mark the rings for the gold band, and press in the rows of pits with a milling tool.

Gerekli aletler:

Metal Torna TezgâhıMetal Torna Tezgâhı
Tırtıl çekme aletiTırtıl çekme aleti
4

Anneal, gild and band

Anneal and brighten the thimbles. Line each inside with a thin cone of gold leaf, bonded to the iron by the hard pressure of a smooth steel mandril. Turn an annular seat outside, lay a gold fillet in it and press its edges into a fine groove cut on the lathe.

Bu adım için malzemeler:

Altın varakAltın varak1 lining
Bilinmeyen metalBilinmeyen metal1 gold fillet

Gerekli aletler:

Demirci OcağıDemirci Ocağı
Mandren çubuğuMandren çubuğu
Metal Torna TezgâhıMetal Torna Tezgâhı

Malzemeler

3

Gerekli Aletler

8

Bu planla yapılan

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...