İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
USB-B Cable: Type-A Plug to Type-B Plug, Wired to the USB 2.0 Specification
Ed

Oluşturan

Ed

4. Kasım 2026FI
24
0
0
0
0

USB-B Cable: Type-A Plug to Type-B Plug, Wired to the USB 2.0 Specification

A USB-B cable joins a computer (Type-A plug) to a device such as an Arduino board or a printer (Type-B plug). The USB 2.0 Specification (USB Implementers Forum, 2000) fixes the wiring: contact 1 VBUS on the red wire, 2 D- white, 3 D+ green, 4 GND black, and the plug shells joined through the cable's shield. It also sets the cable's build and its limits: a twisted green-white data pair, a red-black power pair, foil and braid shields, no more than 26 ns of delay, and less than 0.6 ohm from shell to shell. This rung works out how long the cable may be, then cuts a 1.5 m shielded cable, solders a Type-A plug to one end and a Type-B plug to the other, and checks every wire with a multimeter. Source: Universal Serial Bus Specification Rev. 2.0, sections 6.4.1, 6.5.2, 6.6, 7.1.16, 7.2.2. Picture: our own drawing.
Orta
About 1 hour

Talimatlar

1

How long may it be?

The delay and voltage-drop limits from the specification, and what they allow for each wire size.
2

Cut and strip the cable

Cut 1.5 m of shielded USB cable with a 24 AWG power pair. At each end, slit and remove 20 mm of the PVC jacket with the knife. Comb the braid back over the jacket, trim the foil off and keep the bare drain wire. Strip 3 mm of insulation from the red, black, green and white wires.

Bu adım için malzemeler:

Ekranlı USB kablosuEkranlı USB kablosu1.5 m

Gerekli aletler:

Şerit MetreŞerit Metre
Maket bıçağıMaket bıçağı
Yan keskiYan keski
Kablo soyucuKablo soyucu
Koruyucu gözlükKoruyucu gözlük
3

Solder the Type-A plug

Slide the plug's hood and a 40 mm piece of heat-shrink tubing onto the cable. Tin the wires and solder them to the plug's contacts: 1 red (VBUS), 2 white (D-), 3 green (D+), 4 black (GND). Twist the drain wire into the braid and solder both to the plug's metal shell.

Bu adım için malzemeler:

USB A tipi fişUSB A tipi fiş1 adet
Isıyla daralan makaronIsıyla daralan makaron40 mm
Lehim TeliLehim Teli1 as required

Gerekli aletler:

HavyaHavya
Üçüncü elÜçüncü el
4

Solder the Type-B plug

Do the same at the other end with the Type-B plug: 1 red (VBUS), 2 white (D-), 3 green (D+), 4 black (GND), drain wire and braid to the shell. Pin 1 must reach pin 1 at both ends.

Bu adım için malzemeler:

USB B tipi fişUSB B tipi fiş1 adet
Isıyla daralan makaronIsıyla daralan makaron40 mm
Lehim TeliLehim Teli1 as required

Gerekli aletler:

HavyaHavya
Üçüncü elÜçüncü el
5

Check every wire

With the multimeter, check that each contact connects to the same contact at the other end and to no other, and that no contact touches a shell. Measure from shell to shell: the specification asks for less than 0.6 ohm.

Gerekli aletler:

MultimetreMultimetre
6

Close the plugs

Clip the hoods over the plugs, slide the heat-shrink tubing over each joint between hood and cable, and shrink it with the heat gun as a strain relief.

Gerekli aletler:

Sıcak hava tabancasıSıcak hava tabancası
7

History and honest limits

The specification's revision history dates USB 1.0 to 15 January 1996, 1.1 to 23 September 1998 and 2.0, which added high speed, to 27 April 2000. The specification requires a standard detachable cable to end in OVERMOLDED plugs; ours has hand-soldered plugs in hoods, so it is not a compliant cable. We do not measure its 90 ohm impedance or its delay. The 1.5 m length, the 24 AWG power pair and the strip lengths are ours. How the plugs and the cable are made is not covered (unknown heads).

Malzemeler

5

Gerekli Aletler

9

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...