SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Valved Air-Tube Dasher Churn: A Double-Acting Valve Lets Air Out of a Tube That Swings With the Dashers
William A. Vertrees of Winchester, Missouri, received US 16,203, dated 9 December 1856, for an air tube turning with the dashers, bent horizontal at its foot, with "a double-acting valve" at its mouth that opens on the side away from the motion as the shaft is swung back and forth by a strap from a pulley and lever.
This rung prints the dasher arms, step, elbow, valve flap, clips and pulley, builds the churn and makes butter.
Orta
About 4 hours, plus printing
Talimatlar
1
1
Air from the tube's mouth
Air from the tube's mouth
Jupyter defteri yükleniyor…
2
2
Air drawn into the cream before it
Air drawn into the cream before it
Webster draws air down a turning agitator; Vertrees down a tube with a two-way valve.
3
3
Read US 16,203
Read US 16,203
"It may be seen that as the pipe revolves to the right the inner end of the valve (V,) will be pressed against the right side closing the right side of the aperture and allowing the air to pass out on the left side behind the wing of the valve by centrifugal force and when it revolves in the contrary direction the valve acts on the contrary side with similar effect."
4
4
Print the parts
Print the parts
Print the dasher arms, the cross step, the elbow with its orifice, the valve flap, two tube clips and the pulley. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Bu adım için malzemeler:
PETG filament1 adetGerekli aletler:
FDM 3B yazıcı5
5
Print the dasher arms
Print the dasher arms
The dasher arms, printed as step 4 describes.
6
6
Print the cross step
Print the cross step
The cross step, printed as step 4 describes.
7
7
Print the elbow with its orifice
Print the elbow with its orifice
The elbow with its orifice, printed as step 4 describes.
8
8
Print the valve flap
Print the valve flap
The valve flap, printed as step 4 describes.
9
9
Print the tube clip
Print the tube clip
The tube clip, printed as step 4 describes.
10
10
Print the pulley
11
11
Dashers and air tube
Dashers and air tube
Lay the cross step in a straight-sided round food-grade container about 190 mm across and stand a 10 mm square hardwood shaft in it, the dasher arms on its foot. Pin the flap in the elbow's orifice with a 2 mm stainless pin, glue the elbow on a 20 mm food-grade pipe reaching above the cream, and tie the pipe to the shaft with the clips, between the arms.
Bu adım için malzemeler:
Gıda sınıfı saklama kabı1 adet
Sert ağaç kavelalar1 adet
PVC Boru1 adet
Yumuşak Çelik Çubuk1 adet
İki bileşenli epoksi1 adetGerekli aletler:
El Testeresi
Demir Testeresi12
12
Pulley, strap and lever
Pulley, strap and lever
Stand a pine post beside the churn and mount the pulley on a 10 mm rod near its top. Fix one end of a leather strap to the pulley, wind it round the pulley, take it across and wind it a few turns round the shaft, and fix it. Glue a 12 mm dowel lever into the pulley's socket.
Bu adım için malzemeler:
Çam tahta1 adetYumuşak Çelik Çubuk1 adet
Deri şerit1 adetSert ağaç kavelalar1 adet
#8 x 1" ahşap vidası1 adetGerekli aletler:
El Testeresi
Kablosuz Matkap
Matkap Ucu Takımı
Tornavida takımı13
13
The patent drawing
The patent drawing
US 16,203 drawing sheet, public domain (expired patent).
14
14
Churn
Churn
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 2 litres, below the pipe's top. Raise and lower the lever steadily so the shaft swings back and forth; watch for bubbles near the bottom; time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
Bu adım için malzemeler:
Yağlı krema2000 ml
İri Deniz Tuzu1 adet
Su1 adetGerekli aletler:
Takılı kalan problu termometre
Kronometre
Dijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesi15
15
Troubleshooting
Troubleshooting
Valved air-tube churn troubleshooting.
Flow
Loading...
16
16
History and honest limits
History and honest limits
**William A. Vertrees** of Winchester, Clark County, Missouri, US 16,203, 9 December 1856. The shaft stood in a cross piece laid loosely in the bottom, easy to lift out for washing. He claimed the air tube with its double-acting valve. A container, pipe, pine and printed parts stand in for his; the notebook's speeds are estimates. FDM prints hold food in their layer lines, so wash well and replace when worn.
Malzemeler
12- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 2000 mlYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
Gerekli Aletler
10- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Tasarım dosyaları
6Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler
Air-Chest Spiral Agitator Churn: A Disk That Draws Air Down Its Agitator Into the Cream
Emma tarafından
YİYECEK & İÇECEK
37
0
0
0
0
0
Cord-Wound Staff Churn Drive: A Swinging Lever Twists the Dash To and Fro by Cords
Hoop tarafından
YİYECEK & İÇECEK
33
0
0
0
0
0
Churning Butter from Cream — The 5,000-Year-Old Fat Separation
TheChef tarafından
ZANAAT
55
0
0
0
0
0
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.