İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Counter-Revolving Dasher Churn: Geared Dashers on Offset Shafts Turn Contrary Ways, Their Blades Skewed Contrary Ways
Aaron C. Vaughan of Johnstown, Pennsylvania, received US 27,396, dated 6 March 1860, for churn dashers. Two or more revolving dashers stand end to end in one box on parallel shafts set a little out of line, joined by pinions inside the box so each turns contrary to the next; the blades of each are inclined contrary to the next's. He says the cream then neither whirls round the shafts nor runs to one end.
This builds his two-dasher form (Fig. 1). The patent gives no sizes; every size here is ours.
İleri
About 2 days, plus printing
Talimatlar
1
1
Two dashers, one crank
Two dashers, one crank
Jupyter defteri yükleniyor…
2
2
Two parts turning contrary ways, three weeks before
Two parts turning contrary ways, three weeks before
Ward turns a cylinder against its dashers. Vaughan turns dasher against dasher, side by side in one box.
3
3
Read US 27,396
Read US 27,396
"If straight the force of the current would be around the shaft, but this is counteracted by breaking the line of the shaft, though still keeping them parallel with each other. If the blades were inclined in one direction only, then the cream would be forced to that end of the box toward which the inclination tends."
4
4
Print the pinions a, a
Print the pinions a, a
Spur pinion, module 2.5, 20 teeth, 18 mm wide, with a hub 28 mm across; bored 16.4 mm for the shaft. Print two. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Box A, pillar block E and lid
Box A, pillar block E and lid
From 20 mm hardwood board make a box 700 x 300 mm inside and 300 deep; glue and screw it, and seal the inside joints with silicone sealant. Screw a hardwood pillar block E, 30 x 120 mm and 180 high, upright across the floor's middle, 340 mm from the crank end. Bore it 16.6 mm across at two points 150 mm up, 25 mm either side of the middle. Bore the crank end 17 mm across 150 mm up and 25 mm to one side, for dasher B; bore the other end 16 mm for the set screw b, 25 mm to the other side. Cut a lid to lie on top.
Bu adım için malzemeler:
Sert Ağaç Tahtası3 adet
Ahşap Tutkalı1 adet
Ahşap vidalar40 adetGerekli aletler:
Daire testere tezgâhı
Kablosuz Matkap
Matkap Ucu Takımı
Çubuklu işkence
Tornavida takımı
Şerit Metre
Zımpara Kağıdı6
6
Dashers B and C
Dashers B and C
For each dasher cut four hardwood blades 240 x 40 x 8 mm, two hardwood hubs 36 mm across and 24 long bored 16.4 mm, and eight 12 mm dowel arms. Glue four arms into each hub a quarter turn apart, 220 mm apart along the shaft, and screw the blades across their ends 100 mm from the shaft, each blade skewed 8 degrees to the shaft (one end 31 mm ahead of the other). Skew dasher B's blades one way and C's the other.
Bu adım için malzemeler:
Sert Ağaç Tahtası1 adet
Sert ağaç kavelalar1 adet
Ahşap Tutkalı1 adet
Ahşap vidalar16 adetGerekli aletler:
Daire testere tezgâhı
Kablosuz Matkap
Matkap Ucu Takımı
Demir Testeresi
Çubuklu işkence
Tornavida takımı
Zımpara Kağıdı7
7
Shafts, pinions a, a and set screw b
Shafts, pinions a, a and set screw b
Cut a 16 mm stainless shaft 440 mm long for B: through the crank end, through dasher B and its pinion, into the pillar block. Cut one 386 mm long for C: its pinion in line with B's beside the block, through the block and dasher C, its far end in the set screw's step. The pinions mesh 50 mm apart; pin each to its shaft. For the set screw b cut 90 mm of M16 threaded rod, drill a 16.6 mm step 20 mm deep in its inner end, run it through two nuts either side of the end wall, and fix a hardwood handle on its outer end; screw it in until C turns freely without end play. Fit a hardwood crank 120 mm long with a dowel handle on B's outer end.
Bu adım için malzemeler:
Paslanmaz çelik çubuk2 adet
PETG filament1 adet
Dişli mil1 adet
Altıgen Somun2 adet
Shaft Collar2 adet
Kopilya2 adet
Sert Ağaç Tahtası1 adet
Sert ağaç kavelalar1 adet
Ahşap Tutkalı1 adetGerekli aletler:
FDM 3B yazıcı
Demir Testeresi
Eğeler (El Eğesi)
Tezgah Mengenesi
Kablosuz Matkap
Matkap Ucu Takımı
Kurbağacık anahtar8
8
The build in 3D
The build in 3D
FreeCAD model of this build, one side and the lid left off: dasher B on its shaft from the crank end to the pillar block E, dasher C on the offset shaft from E to the set screw b, and the two pinions a meshing beside E.
9
9
Churn
Churn
Pour in about 15 litres of heavy cream at about 15 °C, checked with the thermometer, put on the lid and turn the crank steadily, timing it: the two dashers turn contrary ways. When the butter comes, lift the lid and the butter out, ladle or tip the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
Bu adım için malzemeler:
Yağlı krema15 l
İri Deniz Tuzu1 adet
Su1 adetGerekli aletler:
Takılı kalan problu termometre
Kronometre
Dijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesi10
10
Troubleshooting
Troubleshooting
Counter-revolving dasher churn troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**Aaron C. Vaughan** of Johnstown, Cambria County, Pennsylvania, US 27,396, 6 March 1860, "Churn-Dasher". He did not claim two or more dashers in one churn, nor turning them contrary ways by gearing, but the series of dashers set lengthwise, geared inside the box, each pair turning contrary ways with blades inclined contrary ways; his Fig. 2 shows three. He does not say how the contrary inclination is measured; ours are mirror images. The patent gives no sizes; every size here is ours, and our pinions are printed.
Malzemeler
14- 3 adetYer Tutucu
- 3 adetYer Tutucu
- 56 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 2 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 2 adetYer Tutucu
- 2 adetYer Tutucu
- 2 adetYer Tutucu
- 15 lYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
Gerekli Aletler
16- 1 vendor sell this, none ship to you yetYer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Tasarım dosyaları
2Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

Counter-Turning Cylinder Churn: The Ribbed Cylinder Turns One Way While the Dashers Inside Turn the Other
Buttercup tarafından
Ağaç işleri
8
0
0
0
0
0

Contrary Hinged-Dasher Air-Pump Churn: Two Crossing Dashers Fold to Gather, a Pump Blows Air Through the Cream
Buttercup tarafından
YİYECEK & İÇECEK
5
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
TheChef tarafından
ZANAAT
63
0
0
0
0
0
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

