İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Washing Machine with Churn: One Crank Pounds the Wash, Turns the Tub and Works a Dash Churn (Wagoner & Severson, 1859)
YourGrandma

Oluşturan

YourGrandma

11. Kasım 2026IS
10
0
0
0
0

Washing Machine with Churn: One Crank Pounds the Wash, Turns the Tub and Works a Dash Churn (Wagoner & Severson, 1859)

John Wagoner and Abram Severson Jr. of Guilderland Center, New York, received US 25,152, dated 16 August 1859, for a washing machine. A crank shaft with a heavy balance wheel rocks a long lever. A springy beam on the lever carries a pounder into the tub, and a belt and a pair of bevel wheels turn the tub slowly under it. The tub stands on a hinged platform: folded up it slackens the belt, and let down the tub's weight tightens it. A pin on the lever also works the dash of a churn standing beside the machine, with or without the washing. The patent gives no sizes; every size here is ours.
İleri
About 5 days, plus printing

Talimatlar

1

Crank pin, strokes and tub speed

Jupyter defteri yükleniyor…
2

One crank working a churn and a washtub, a year before

Swan's machine lifted a plunger by a cam. Here a springy beam carries the pounder, and the tub's own weight tightens the belt that turns it.
3

Read US 25,152

"In addition to what has now been described our machine is adapted to operate a churn very effectively either alone or simultaneously with the washing operation." "We place the center of our tube J out of the plane of the motion of the levers T and V. Our pounder therefore inclines to strike on one side of J and not in the center thereby increasing the uniformity of the effect on the contents."
4

Print the pulley for shaft D

Flat-faced pulley 120 mm across and 40 mm wide, bored 31 mm for shaft D. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Tasarım DosyasıSTLCC0 - Free
5

Print pulley R

Flat-faced pulley 100 mm across and 40 mm wide, bored 21 mm for the lower bevel wheel's shaft. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Tasarım DosyasıSTLCC0 - Free
6

Frame A, legs B and uprights C

From 70 x 70 mm timber cut three stringers 1500 mm, two cross pieces 630 mm, four legs 700 mm, an upright 830 mm and an upright 720 mm. Bolt the cross pieces across the tops of the legs and the stringers on the cross pieces, 210 mm apart, so the frame's top is 840 mm from the floor. Bolt the long upright to the outside of the front stringer 100 mm from the left end and the short one 100 mm from the right end. Chisel an opening 50 x 260 mm through the left upright, from 440 to 700 mm above the stringer, and bore it across 560 mm up for pin v (a 16 mm bolt).

Bu adım için malzemeler:

Yumuşak ağaç 70x70 mmYumuşak ağaç 70x70 mm11 m
Kare boyunlu yuvarlak başlı cıvataKare boyunlu yuvarlak başlı cıvata16 adet
Düz PulDüz Pul16 adet
Naylon Fiberli Emniyet SomunuNaylon Fiberli Emniyet Somunu16 adet

Gerekli aletler:

El TesteresiEl Testeresi
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Yassı matkap ucu takımıYassı matkap ucu takımı
Zıvana yuvası kalemiZıvana yuvası kalemi
Ahşap TokmakAhşap Tokmak
Marangoz gönyesiMarangoz gönyesi
Şerit MetreŞerit Metre
Kurbağacık anahtarKurbağacık anahtar
Çubuklu işkenceÇubuklu işkence
7

Shaft D, balance wheel F and crank E

Bolt three bearing blocks on the stringers' tops 650 mm from the left end and pass a 30 mm steel shaft D through them, 710 mm long. Build the balance wheel from three layers of 20 mm hardwood segments glued crossways: 840 mm across, a 100 mm rim and four spokes, 50 mm thick in all. Fit it on D between the front and middle stringers, the printed pulley between the middle and back stringers, and a hand crank 240 mm long on the back end. On the front end fit crank E, a hardwood arm 20 mm thick with a slot from 50 to 125 mm out, and a 20 mm bolt in the slot for the crank pin e.

Bu adım için malzemeler:

Paslanmaz çelik çubukPaslanmaz çelik çubuk1 adet
Rulman yatağıRulman yatağı3 adet
Sert Ağaç TahtasıSert Ağaç Tahtası3 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Altıköşe cıvata takımıAltıköşe cıvata takımı13 adet
Naylon Fiberli Emniyet SomunuNaylon Fiberli Emniyet Somunu13 adet
Shaft CollarShaft Collar2 adet

Gerekli aletler:

Dekupaj TestereDekupaj Testere
PusulaPusula
Daire testere tezgâhıDaire testere tezgâhı
Kablosuz MatkapKablosuz Matkap
Yassı matkap ucu takımıYassı matkap ucu takımı
Freze motoruFreze motoru
Çubuklu işkenceÇubuklu işkence
Demir TesteresiDemir Testeresi
Kurbağacık anahtarKurbağacık anahtar
8

Lever T, link U and rod V

Cut lever T from hardwood 40 x 70 mm, 1195 mm long. Bolt it to the front of the right upright, 610 mm above the stringer, free to rock. Join it to the crank pin by link U, hardwood 20 x 40 mm with its pin holes 560 mm apart, 715 mm from T's pivot. At T's left end join rod V, hardwood 30 x 40 mm, slotted 22 mm wide for 220 mm, and pass it through the left upright's opening astride pin v. Fix a steel pin 3, 24 mm and 370 mm long, through T 1015 mm from its pivot, sticking out at the front for the churn.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası2 adet
Altıköşe cıvata takımıAltıköşe cıvata takımı4 adet
Düz PulDüz Pul8 adet
Naylon Fiberli Emniyet SomunuNaylon Fiberli Emniyet Somunu4 adet
Paslanmaz çelik çubukPaslanmaz çelik çubuk1 adet

Gerekli aletler:

Daire testere tezgâhıDaire testere tezgâhı
Freze motoruFreze motoru
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Yassı matkap ucu takımıYassı matkap ucu takımı
Demir TesteresiDemir Testeresi
Zımpara KağıdıZımpara Kağıdı
Kurbağacık anahtarKurbağacık anahtar
Şerit MetreŞerit Metre
9

Spring beam W and the pounder

Cut the spring beam W from ash 30 x 40 mm, 1210 mm long. Lay it on T's top, its left end against a block glued on T, bolt it through T 415 mm left of the pivot with a wing nut (the hand nut w), and let it run past the upright to overhang the frame by 510 mm. Make rod X from hardwood 40 x 40 mm, 1090 mm long, with four holes at its top for height. Under it glue a hardwood head 200 x 120 mm with five legs 30 x 36 mm, 160 mm long, each slotted (Z) and bored across (z). Hang X from W's end on a bolt so it swings freely, in front of W.

Bu adım için malzemeler:

Dişbudak tahtaDişbudak tahta1 adet
Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Altıköşe cıvata takımıAltıköşe cıvata takımı2 adet
Kanatlı somunKanatlı somun1 adet
Düz PulDüz Pul4 adet

Gerekli aletler:

Daire testere tezgâhıDaire testere tezgâhı
Freze motoruFreze motoru
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Zıvana yuvası kalemiZıvana yuvası kalemi
Ahşap TokmakAhşap Tokmak
Zımpara KağıdıZımpara Kağıdı
Çubuklu işkenceÇubuklu işkence
10

Hinged platform M, bevel wheels and platform K

Make platform M from 40 mm hardwood, 860 x 860 mm, and hang it on two strap hinges (the butts m) at the feet of the right-hand legs. On M, 100 mm from the hinges, fit a 20 mm vertical shaft in a flange bearing with pulley R and the lower bevel wheel on it. In a hardwood post fit a 20 mm cross shaft with the upper bevel wheel and a 240 mm hardwood pulley P in line with the pulley on D. 480 mm from the hinges, 340 mm towards the front, set a 24 mm shaft L in a hardwood block that slides in a slot along M, with a compression spring pushing it away from R. Glue platform K, 660 mm across and 40 mm thick, bore it for L, and set four 40 mm hardwood wheels l under its edge.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası4 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Demir şerit menteşeDemir şerit menteşe2 adet
Flanşlı rulmanFlanşlı rulman3 adet
Konik dişli takımı (çelik, 1:1)Konik dişli takımı (çelik, 1:1)1 adet
Paslanmaz çelik çubukPaslanmaz çelik çubuk1 adet
Shaft CollarShaft Collar3 adet
Basma yay takımıBasma yay takımı1 adet
Sert ağaç kavelalarSert ağaç kavelalar1 adet
Ahşap vidalarAhşap vidalar40 adet
Altıköşe cıvata takımıAltıköşe cıvata takımı4 adet
Naylon Fiberli Emniyet SomunuNaylon Fiberli Emniyet Somunu4 adet
PETG filamentPETG filament1 adet

Gerekli aletler:

FDM 3B yazıcıFDM 3B yazıcı
Dekupaj TestereDekupaj Testere
PusulaPusula
Freze motoruFreze motoru
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Yassı matkap ucu takımıYassı matkap ucu takımı
Demir TesteresiDemir Testeresi
Çubuklu işkenceÇubuklu işkence
Kurbağacık anahtarKurbağacık anahtar
11

Belts O and S, and the fold

Put belt S round pulley R and platform K's rim. Fold M up against the frame, run a string round the pulley on D and pulley P, and choose belt O just short enough that, with M let down and empty, it holds M at a slight angle; "The belt O is sufficiently short to hold the platform M at a slight angle until the weight of J is added thereto." Set the wooden tub J on K: its weight should pull M flat and the belt tight. Oil the wood.

Bu adım için malzemeler:

Tahrik kayışıTahrik kayışı2 adet
Ahşap tekneAhşap tekne1 adet
Kaynatılmış Bezir YağıKaynatılmış Bezir Yağı1 adet

Gerekli aletler:

Şerit MetreŞerit Metre
12

The build in 3D

FreeCAD model of this build: the frame, shaft D with the balance wheel and crank E, lever T with link U and rod V, the spring beam W and the pounder in the tub (front of the tub cut away), the hinged platform M with the bevel wheels, pulleys and belts, and the churn on pin 3. The crank was turned through 18 positions.
Tasarım DosyasıBLENDCC0 - Free
13

Wash

Put warm water, soap and the clothes in the tub, and set the pounder's height so its feet clear the tub's bottom by the clothes. Turn the hand crank steadily. The pounder rises and falls on one side of the tub while the tub turns under it, so every part of the wash comes under it in turn. Move the crank pin out in its slot for a longer stroke, in for a shorter one. Lift the clothes out to rinse and wring.

Gerekli aletler:

SuSu
Kalıp sabunKalıp sabun
14

Churn on pin 3

Make the dash 2: a hardwood rod 35 mm across, 1250 mm long, bored at the top to hang on pin 3, with two crossed blades 220 x 30 x 20 mm at the bottom. Stand the churn under pin 3, beside the machine, pour in about 10 litres of cream at about 15 °C (checked with the thermometer), a third of its height, pass the dash through the lid and hang it on pin 3. Turn the crank, with or without the wash, timing it. When the butter comes, lift the dash off the pin, drain the buttermilk, wash the butter in cold water, salt and weigh it.

Bu adım için malzemeler:

Yağlı kremaYağlı krema10 l
İri Deniz Tuzuİri Deniz Tuzu1 adet
Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Sert ağaç kavelalarSert ağaç kavelalar1 adet

Gerekli aletler:

YayıkYayık
Takılı kalan problu termometreTakılı kalan problu termometre
KronometreKronometre
Dijital Mutfak TerazisiDijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesiBüyük paslanmaz çelik karıştırma kâsesi
SuSu
Kablosuz MatkapKablosuz Matkap
Yassı matkap ucu takımıYassı matkap ucu takımı
El TesteresiEl Testeresi
15

Troubleshooting

Washing machine troubleshooting.

Flow

Loading...
16

History and honest limits

**John Wagoner and Abram Severson, Jr.** of Guilderland Center, New York, US 25,152, 16 August 1859, "Washing-Machine". They claimed mounting the platform K and the pulleys and gearing P Q R on the hinged platform M, so turning M up slackens belt O and turning it down lets the tub's weight tighten it. The patent gives no sizes; every size here is ours. Their hand lever H and rod I, a second way to turn D, are not built: we turn D by a crank, which the patent allows. The spring that urges K's centre against belt S is "not represented" in their drawing; ours is a compression spring in a slot.

Malzemeler

24

Gerekli Aletler

24

Tasarım dosyaları

3
  • wagoner-severson-washing-machine-with-churn-pulley-d.stlSTLCC0
  • wagoner-severson-washing-machine-with-churn-pulley-r.stlSTLCC0
  • wagoner-severson-washing-machine-with-churn.blendBLENDCC0

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...