İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Wheelbarrow: a Small Wooden Barrow (Cassell's, 1900)
Woody

Oluşturan

Woody

4. Kasım 2026NO
12
0
0
0
0

Wheelbarrow: a Small Wooden Barrow (Cassell's, 1900)

A small wooden wheelbarrow: ash hales (handles) framed with oak cross-pieces, splayed legs, a red-deal bottom and sides with a curved front board bound in hoop iron, and a 1 ft wheel of eight oak spokes and four ash felloes on an ash or oak axle. Painted red inside and light green outside, lined in a lighter colour and black. Source: P. N. Hasluck, Cassell's Cyclopaedia of Mechanics (1900), p. 176. Picture: the book's Figs. 1-2.
Orta
Unknown

Talimatlar

1

Make the hales

Cut the two ash hales 3 ft 1 in long, 1 5/8 in deep by 1 1/2 in thick, the handles rising 3 3/4 in above the underside. Leave no more than 5/8 in on the faces of the hale tops; dress out 3/8 in on the face and 1/4 in underneath.

Bu adım için malzemeler:

Dişbudak tahtaDişbudak tahta1 hales 3 ft 1 in x 1 5/8 x 1 1/2 in

Gerekli aletler:

El TesteresiEl Testeresi
El rendesiEl rendesi
Çift saplı rendeÇift saplı rende
2

Frame with oak cross-pieces

Make the cross-pieces of oak, edges dressed off underneath. Let the hind piece's tenons, gauged 1/2 in thick, come through the hales 1 1/4 in to support the legs (Fig. 2). Pin the hales and cross-pieces tight with 3/16 in wood pins.

Bu adım için malzemeler:

Ak meşe tahtaAk meşe tahta1 adet
Ahşap kavelaAhşap kavela1 3/16 in pins

Gerekli aletler:

Sırtlı testereSırtlı testere
Zıvana yuvası kalemiZıvana yuvası kalemi
Çizecek (markalama mastarı)Çizecek (markalama mastarı)
Kol matkabı ve ucuKol matkabı ve ucu
Ayarlı gönyeAyarlı gönye
3

Fit the legs and stays

Put on legs 1 1/2 in square, splayed at the top, standing 1 ft below the hales to suit a 1 ft wheel, with no more than a 1/4 in shoulder. Fasten legs to hales with 3 in bolts, heads outside. Fit four stays: two under the hales and two under the hind cross-pieces.

Bu adım için malzemeler:

Ak meşe tahtaAk meşe tahta1 legs 1 1/2 in square, stays
Kare boyunlu yuvarlak başlı cıvataKare boyunlu yuvarlak başlı cıvata4 3 in

Gerekli aletler:

El TesteresiEl Testeresi
Kol matkabı ve ucuKol matkabı ve ucu
Tornavida takımıTornavida takımı
4

Bottom and sides

Put in the bottom board of 1/2 in red deal, overhanging the front cross-piece 5/8 in; paint all joints. Fit the sides to the hales, the front leaning up to 3 3/4 in beyond square; sides 9 in deep by 5/8 in thick, reduced to 8 1/4 in at the hind ends, front ends edged. Run a 3/16 in or 1/4 in bead on the edge.

Bu adım için malzemeler:

Çam tahtaÇam tahta1 1/2 in bottom, 5/8 in sides
Yağlı boyaYağlı boya1 adet

Gerekli aletler:

El TesteresiEl Testeresi
El rendesiEl rendesi
Fırça setiFırça seti
5

Front board and ironwork

Fit the front board, of 3/4 in red deal or elm, on top of the hales and bottom board, rising in a curve 1 1/4 in above the sides. Paint the joints and nail the sides to it with 1 1/2 in cut nails; screw on the 7/8 in hoop iron with 3/4 in round-headed screws.

Bu adım için malzemeler:

Çam tahtaÇam tahta1 3/4 in front board
Demir ÇivilerDemir Çiviler1 1 1/2 in cut nails
Yumuşak Çelik LamaYumuşak Çelik Lama1 7/8 in hoop iron
Ahşap vidalarAhşap vidalar1 3/4 in round-headed
Yağlı boyaYağlı boya1 adet

Gerekli aletler:

El TesteresiEl Testeresi
ÇekiçÇekiç
Tornavida takımıTornavida takımı
Fırça setiFırça seti
6

Make the wheel

Turn an ash or oak axle 8 1/4 in long by 2 1/2 in, its ends turned down to 1 1/2 in for ferrules 1 in long; drive 3/8 in round pins into the ends to stand out 1 in. Fit eight oak spokes 3/4 in by 1/2 in and four ash felloes 1 1/4 in square, joined with four 1/4 in dowels and bevelled to take a 3/4 in by 1/8 in hoop, rounded inside.

Bu adım için malzemeler:

Dişbudak tahtaDişbudak tahta1 axle and felloes
Ak meşe tahtaAk meşe tahta1 spokes
Yuvarlak demir çubukYuvarlak demir çubuk1 3/8 in pins
Ahşap kavelaAhşap kavela4 1/4 in
Yumuşak Çelik LamaYumuşak Çelik Lama1 3/4 x 1/8 in tyre

Gerekli aletler:

Ahşap torna tezgâhıAhşap torna tezgâhı
Çift saplı rendeÇift saplı rende
Kol matkabı ve ucuKol matkabı ve ucu
ÇekiçÇekiç
7

Hang the wheel and paint

Screw under each hale an iron 3/4 in broad by 1/8 in thick, long enough to pass the front cross-piece by 2 or 3 in, its eye taking the axle pin. Paint the wheel and the inside of the barrow red, the outside light green, lined in a lighter colour and black.

Bu adım için malzemeler:

Yumuşak Çelik LamaYumuşak Çelik Lama2 3/4 x 1/8 in irons
Ahşap vidalarAhşap vidalar1 adet
Yağlı boyaYağlı boya1 adet

Gerekli aletler:

Tornavida takımıTornavida takımı
Fırça setiFırça seti

Malzemeler

10

Gerekli Aletler

12

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...