İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Spring-Bow Churn: A Bow With Two Springs Keeps Its Cord Tight Round a Screw Whirl on the Crank Shaft
Buttercup

Oluşturan

Buttercup

11. Kasım 2026IE
12
0
0
0
0

Spring-Bow Churn: A Bow With Two Springs Keeps Its Cord Tight Round a Screw Whirl on the Crank Shaft

Abner Willson of Colden, New York, received US 27,181, dated 14 February 1860, for a churn worked like a bow drill. A cord from a stiff bow takes a turn round a screw whirl on the crank shaft; pushing and drawing the bow spins the crank, which lifts and drops the dasher. Two springs on the bow, one near each end, hold the cord, so it stays tight both ways and does not slip. The patent gives no sizes; every size here is ours.
Orta
About 2 days, plus printing

Talimatlar

1

From bow strokes to dasher strokes

Jupyter defteri yükleniyor…
2

The bow and cord that turn a spindle

A bow drill's cord, wrapped round a spindle, turns it back and forth. Willson puts the same bow on a churn.
3

A crank that strokes a dasher, the year before

Austin's crank lifts and drops a dasher. Willson turns his crank with a bow instead of a handle.
4

Read US 27,181

"The effect of these two springs on an inflexible bow is to keep the cord always at a proper tension; in a flexible bow constructed as is customary, (unless the cord is very tense) when the bow is pushed, that portion of the cord between the whirl and the hither end of the bow slackens; and when the bow is drawn, that portion of the cord between the whirl and farther end of the bow slackens; this slackening which causes a slipping and a loss of power, is avoided by my peculiarly constructed bow. The threads of the whirl keep the cord from chafing."
5

Print the screw whirl D

Whirl 50 mm across and 60 long with a helical groove at 6 mm pitch for the cord, and a hub 36 mm across; bored 12.4 mm for the crank shaft. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Tasarım DosyasıSTLCC0 - Free
6

Print the dasher B

Cone dasher 160 mm across, open underneath, with a socket 20.6 mm across for the dasher rod. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Tasarım DosyasıSTLCC0 - Free
7

Crank shaft C and dasher B

Drill a 13 mm hole through each side of the bucket, opposite each other, 300 mm above the inside floor. Cut a 12 mm stainless rod 450 mm long. Glue a 20 mm hardwood dowel 220 mm long into the dasher's socket, and drill 12.6 mm across its top end, 12 mm from the end. Starting 155 mm from one end, bend a crank 40 mm deep and 40 mm wide in the vise; slide the dasher rod's eye onto the crank pin before bending the second side. Pass the shaft through the bucket's holes with the crank inside, centred, and fit a collar on the short end. Seal round both holes outside with silicone sealant.

Bu adım için malzemeler:

20 Litrelik Kova20 Litrelik Kova1 adet
Paslanmaz çelik çubukPaslanmaz çelik çubuk1 adet
Sert ağaç kavelalarSert ağaç kavelalar1 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Shaft CollarShaft Collar1 adet
Silikon Dolgu MacunuSilikon Dolgu Macunu1 adet
PETG filamentPETG filament1 adet

Gerekli aletler:

FDM 3B yazıcıFDM 3B yazıcı
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Demir TesteresiDemir Testeresi
Tezgah MengenesiTezgah Mengenesi
Eğeler (El Eğesi)Eğeler (El Eğesi)
Şerit MetreŞerit Metre
8

Fix the screw whirl D

Slide the whirl onto the long end of the shaft outside the bucket, hub towards the bucket, 10 mm clear of it. Drill 4 mm through the hub and shaft, and drive in a 4 mm stainless pin cut from rod, so the whirl is "firmly attached to the crank shaft".

Bu adım için malzemeler:

Paslanmaz çelik çubukPaslanmaz çelik çubuk1 adet

Gerekli aletler:

Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Demir TesteresiDemir Testeresi
Eğeler (El Eğesi)Eğeler (El Eğesi)
Tezgah MengenesiTezgah Mengenesi
9

Bow F with springs a and cord E

Cut a hardwood bow 700 x 50 x 30 mm, the patent's "inflexible bow", and plane and sand its underside slightly curved. Fit a dowel through one end as a handle, as in Fig. 1. Screw a spring-steel strip 120 x 16 mm by its inner end to the upper side near each end, outer ends free and reaching the bow's ends; drill a 5 mm hole through the bow under each spring's outer end and a 5 mm hole in each spring's tip. Pass a 4 mm cord up through each bow hole and tie it to the spring's tip, leaving enough slack between to take one turn round the whirl with the springs bent down a little.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Sert ağaç kavelalarSert ağaç kavelalar1 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Yay çeliği şeridiYay çeliği şeridi2 adet
Ahşap vidalarAhşap vidalar4 adet
KordonKordon1 adet

Gerekli aletler:

Daire testere tezgâhıDaire testere tezgâhı
Zımpara KağıdıZımpara Kağıdı
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Demir TesteresiDemir Testeresi
Eğeler (El Eğesi)Eğeler (El Eğesi)
Tezgah MengenesiTezgah Mengenesi
Çubuklu işkenceÇubuklu işkence
Tornavida takımıTornavida takımı
10

The build in 3D

FreeCAD model of this build, the bucket cut through the middle: the crank shaft with its 40 mm crank, the dasher hanging from the crank pin, the screw whirl outside, and the bow with its two springs and cord.
Tasarım DosyasıBLENDCC0 - Free
11

Churn

Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket and put on its lid. Lay the cord in the whirl's groove with one turn round it, have someone steady the bucket or hold it between your feet, and push and draw the bow steadily, timing it. When the butter comes, take off the lid, lift the butter out past the dasher, tip the buttermilk out into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Bu adım için malzemeler:

Yağlı kremaYağlı krema8 l
İri Deniz Tuzuİri Deniz Tuzu1 adet
SuSu1 adet

Gerekli aletler:

Takılı kalan problu termometreTakılı kalan problu termometre
KronometreKronometre
Dijital Mutfak TerazisiDijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesiBüyük paslanmaz çelik karıştırma kâsesi
12

Troubleshooting

Spring-bow churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Abner Willson** of Colden, Erie County, New York, US 27,181, 14 February 1860, "Churn". He claimed "the bow F with springs a when constructed as described, in combination with screw whirl D operating as set forth"; he did not claim the treadles G he also shows, nor the dasher, crank shaft or vessel. His vessel is a tall wooden one; ours is a food-grade bucket, and the cone dasher, its rod and our way of fixing the whirl are ours. The patent gives no sizes; every size here is ours.

Malzemeler

14

Gerekli Aletler

15

Tasarım dosyaları

3

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...