İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Wood Lathe: Simple Amateur's Lathe with a Maple Bed, 7 in Swing (Lathe Work for Beginners, 1922)
A wood-turning lathe an amateur can build: two strips of hard maple bolted to maple legs make the 3 ft bed, and cast-iron head-stock, tail-stock, hand-rest body, hand wheels and cone pulleys are cast from home-made patterns. Steel spindles turn in the cast-iron bearings, and a cone pulley drives the head-stock from a countershaft.
Result: a wood lathe with a 7 in swing and a 3 ft bed.
Source: R. F. Yates, Lathe Work for Beginners (1922), Chapter XII, pp. 208-216. Unknown: the pattern sizes (on the book's drawings) and the drive. Picture: Fig. 157 of the book.
İleri
Unknown
Talimatlar
1
1
Make the patterns and get castings
Make the patterns and get castings
Make patterns from any handy wood: one for both head-stock and tail-stock, with a web joining the two bearings so the casting does not spring; one for the hand wheels (three castings); one for the washers (two); the cone pulley (two: lathe and countershaft); and the hand-rest body. Give them a slight draw taper. Have them cast in iron at a foundry. Not given: pattern sizes (on the book's drawings).
Bu adım için malzemeler:
Dökme demir parçalar1 head-stock, tail-stock, wheels, washers, pulleys, rest bodyGerekli aletler:
Kereste tahtası
Kupol ocağı
Bilinmeyen ölçüler2
2
Build the maple bed
Build the maple bed
Make the bed of two strips of clear hard maple 1 in thick, 4 in wide and about 36 in long (about 1 1/2 in thick for a longer bed), and two maple legs, the part between the ways cut exactly square. Bore a 5/8 in hole through the head-stock leg in line with the head-stock's 1/2 in tapped hole, recessed below for a nut and washers. Bolt bed to legs with eight 3/8 in carriage bolts. Sand it and give it a coat of clear shellac against warping. White oak will do if there is no maple.
Bu adım için malzemeler:
Sert ağaç kalası1 ways and legs
Kare boyunlu yuvarlak başlı cıvata8 3/8 in carriage bolts
Gomalak1 finishGerekli aletler:
Sütunlu Matkap
Zımpara Kağıdı3
3
Machine the stocks
Machine the stocks
Face the outside ends of the head-stock and tail-stock bearings on a shaper or milling machine. Drill the bearings between centres in a lathe with a 47/64 in drill, saw off the joining web, face the inner ends and ream to 3/4 in. Line both castings up on a 3/4 in shaft and machine their bottoms. Drill oil holes in the head-stock lugs. Tap the tail-stock front lug 3/16 in for a clamp turned, heated and bent to shape, with soft copper or brass under it; tap the tail-stock rear bearing 7/8 in, 9 threads.
Bu adım için malzemeler:
Bilinmeyen metal1 clamp and copper padGerekli aletler:
Freze Tezgâhı
Metal Torna Tezgâhı
Kılavuz ve pafta takımı
Demirci Ocağı4
4
Turn the spindles and pulley
Turn the spindles and pulley
Turn the head-stock spindle from 1 3/8 in machine steel: 3/4 in diameter, a 7/8 in nose threaded 9 to the inch, a 3/8 in hole right through and a No. 1 Morse taper in the nose. Turn the tail-stock spindle from 7/8 in stock, 3/4 in diameter with a 7/8 in, 9-thread part. Centre each piece, drill halfway from each end with a 3/8 in drill, ream, then finish between centres. Turn the cone pulley with crowned faces, wide enough to run easily between the bearings, and fix it to the spindle with a 3/8 in headless set screw.
Bu adım için malzemeler:
Yumuşak çelik yuvarlak çubuk1 spindles
Bilinmeyen metal1 set screwsGerekli aletler:
Metal Torna Tezgâhı
Sütunlu Matkap5
5
Fit the wheels and hand rest, and assemble
Fit the wheels and hand rest, and assemble
Drill hand wheel N 3/4 in for the tail-stock spindle and hold it with a 1/4 in set screw; tap the other two wheels 1/2 in. Drill the washers 9/16 in. Bolt the head-stock down with a stud through the leg, and fit a 1/2 in stud about 7 in long for the tail-stock and a 1/2 in square-headed bolt for the hand-rest body. Plane the hand rest's bottom, drill it 3/4 in, and fit tee-rests of 1/4 x 1 in flat steel welded to 3/4 in shafting, held by a 1/4 in set screw; make several lengths. The cast iron serves as bearing metal, or the bearings can be bushed or babbitted.
Bu adım için malzemeler:
Yumuşak Çelik Lama1 tee-rests
Bilinmeyen metal1 studs, bolts, set screws, shaftingGerekli aletler:
Sütunlu Matkap
Kılavuz ve pafta takımı
Demirci OcağıMalzemeler
7- 1 head-stock, tail-stock, wheels, washers, pulleys, rest bodyYer Tutucu
- 1 ways and legsYer Tutucu
- 8 3/8 in carriage boltsYer Tutucu
- 1 finishYer Tutucu
- 1 studs, bolts, set screws, shaftingYer Tutucu
- 1 spindlesYer Tutucu
- 1 tee-restsYer Tutucu
Gerekli Aletler
9- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Bağlı Plan Malzemeleri

%10 Atıf
Casting Iron in a Cupola Furnace — Re-Melting Pig Iron into Finished Castings
Piett tarafından
Metal işleme
53
0
0
0
6
0

%10 Atıf
Oak Boards and Blocks, Milled and Air-Dried
Woody tarafından
Ağaç işleri
46
0
0
0
3
0

%10 Atıf
Mild Steel Bar Stock Forged from an Ingot
Forge tarafından
Modern
46
0
0
0
5
0

%10 Atıf
Shellac Flakes from Stick Lac
Mary tarafından
Ağaç işleri
38
0
0
0
1
0

%10 Atıf
Screws: Cold Headed and Thread Rolled
Emma tarafından
Metal işleme
54
0
0
0
1
0
Bu planla yapılan
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.
