İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Workbench: a Pine Bench with a Laminated Maple Top and Vise (Boy Mechanic, 1913)
Woody

Oluşturan

Woody

4. Kasım 2026NO
8
0
0
0
0

Workbench: a Pine Bench with a Laminated Maple Top and Vise (Boy Mechanic, 1913)

The same pine bench with a harder top: 14 maple strips set on edge, glued and screwed together, with a back board, a tool rack and a wooden vise on an iron bench screw. Source: C. E. McKinney, Jr., 'Homemade Workbench', The Boy Mechanic, Book 1 (1913), pp. 442-443. Picture: Figs. 1-3 of the book.
Orta
Unknown

Talimatlar

1

Make the two leg frames

Cut four 2 x 4 in pine legs 23 in long with a tenon on each end 1/2 in thick, 3 1/2 in wide and 1 1/2 in long (Fig. 1, A and B). Cut four crosspieces of the same stock 20 in long, mortised in the narrow edge 1 1/4 in from each end, and slope their corners from the leg out to the middle. Fit each pair of legs to a pair of crosspieces to make the two supports.

Bu adım için malzemeler:

Çam keresteÇam kereste1 2 x 4 in: legs, crosspieces

Gerekli aletler:

El TesteresiEl Testeresi
Zıvana yuvası kalemiZıvana yuvası kalemi
ÇekiçÇekiç
2

Brace them together

Join the supports with two 2 x 4 in braces 24 in long, ends sawn square. Bore through each leg and 4 in into the centre of each brace end, bore an intersecting hole on the back of each brace for the nut, and draw each joint tight with a 3/8 x 6 in bolt (Fig. 2, J). A cross brace on the back stops rocking when planing.

Bu adım için malzemeler:

Çam keresteÇam kereste1 2 x 4 in: braces
Kare boyunlu yuvarlak başlı cıvataKare boyunlu yuvarlak başlı cıvata4 3/8 x 6 in

Gerekli aletler:

El TesteresiEl Testeresi
Kol matkabı ve ucuKol matkabı ve ucu
Kurbağacık anahtarKurbağacık anahtar
3

Build up the maple top

Make the main top M of 14 maple strips 7/8 in thick, 2 in wide and 3 1/2 ft long, set on edge, each glued and screwed to the next, all with the grain one way so it planes smooth. Rabbet its back edge 1/2 in to take a back board N of the same length, 8 1/2 in wide and 7/8 in thick. Screw the top to the top crosspieces with long screws.

Bu adım için malzemeler:

Bilinmeyen malzemeBilinmeyen malzeme14 maple strips 7/8 x 2 in x 3 1/2 ft
Ahşap TutkalıAhşap Tutkalı1 adet
Çam tahtaÇam tahta1 back board
Ahşap vidalarAhşap vidalar1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Blok rendeBlok rende
Düz tornavidaDüz tornavida
4

Add the tool rack

Nail a board E 10 in wide to the back of the bench and fasten a 2 1/2 in board F on top of it at right angles; both 7/8 in thick and 3 1/2 ft long. Bore holes or cut notches in F to hold tools.

Bu adım için malzemeler:

Çam tahtaÇam tahta2 7/8 in, 3 1/2 ft
ÇivilerÇiviler1 adet

Gerekli aletler:

Kol matkabı ve ucuKol matkabı ve ucu
El TesteresiEl Testeresi
ÇekiçÇekiç
5

Fit the vise

Fasten an iron bench screw in a 2 x 6 in block 12 in long. Mortise two guide rails 7/8 x 1 1/2 in and 20 in long into the block; they slide in mortises in a 2 x 4 piece L bolted under the top, which holds the bench-screw nut between the two mortises. Nail L to a top crosspiece and to a 2 x 4 piece P bolted under the top at the end (Fig. 3).

Bu adım için malzemeler:

Çam keresteÇam kereste1 2 x 6 block, 2 x 4 pieces, guide rails
Oymacılık tezgâh vidasıOymacılık tezgâh vidası1 adet
Kare boyunlu yuvarlak başlı cıvataKare boyunlu yuvarlak başlı cıvata1 for L and P
ÇivilerÇiviler1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Zıvana yuvası kalemiZıvana yuvası kalemi
Kol matkabı ve ucuKol matkabı ve ucu
Kurbağacık anahtarKurbağacık anahtar
ÇekiçÇekiç

Malzemeler

8

Gerekli Aletler

7

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...