МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗЕЛЕНЕ МАЙБУТНЄ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Building a Balafon — The West African Gourd-Resonated Xylophone
Woody

Створено

Woody

3. липень 2026NO
0
0
0
0
0

Building a Balafon — The West African Gourd-Resonated Xylophone

Build a balafon: a row of tuned wooden bars, each hung over its OWN tuned gourd resonator with a little buzzing membrane, struck with rubber-headed mallets. Cut and tune the bars by shaving, hang them on a frame over the gourds, and play. A serious maker build in the tuned wooden bar and the individually-tuned resonator.
Середній
Several hours over a couple of sessions

Інструкції

1

Wooden bars over singing gourds

The balafon is a xylophone of tuned wooden bars, but each bar hangs over its own tuned gourd resonator with a small buzzing membrane, giving it a warm, humming, buzzy voice.
2

Cut the bars

Cut a set of hard, dense wooden bars in graduated lengths, longest to shortest, and dry them well. A shorter, thicker bar rings higher.

Матеріали для цього кроку:

Bloodwood BoardBloodwood Board1 штука

Необхідні інструменти ({count})

HacksawHacksaw
3

Tune the bars

Tune each bar by shaving wood away: hollow the MIDDLE of the underside to lower its note, or trim the ENDS to raise it — the same two cuts as any xylophone or marimba.

Необхідні інструменти ({count})

Sloyd Carving KnifeSloyd Carving Knife
4

Build the frame

Build an open frame — two long rails on legs — to carry the bars in a row with space beneath for the gourds.

Матеріали для цього кроку:

Dry Softwood BoardDry Softwood Board1 штука
PVA Wood GluePVA Wood Glue1 штука
5

Fit the gourd resonators

Hang a gourd of the right SIZE beneath each bar — a bigger gourd for a lower bar. Each gourd's air cavity is tuned to its bar so it swells that note like a bottle blown at the right pitch.

Матеріали для цього кроку:

Mature Bottle GourdMature Bottle Gourd6 штук
6

Add the buzzing membranes

Pierce a small hole in the side of each gourd and cover it with a thin membrane (traditionally spider-egg-sac film; tissue works). It buzzes when the bar sounds — the balafon's signature rasp.

Необхідні інструменти ({count})

AwlAwl
7

Hang the bars and play

Rest the bars on cords along the rails at their still points (nodes) so they ring freely, and strike them with two rubber-headed mallets.

Матеріали для цього кроку:

Abaca Tying TwineAbaca Tying Twine1 штука
Dowel RodDowel Rod1 штука
8

Compendium — the bar and its own resonator

The balafon is a tuned-bar idiophone, just like the gamelan's metal saron, and its bars follow the same physics: a struck bar bends and rings, higher when it is short, thick and stiff, and it is tuned by removing wood — hollow the middle to lower the note, trim the ends to raise it — while resting the bar on cords at its two nodes (the still points about a fifth in from each end) lets it ring freely. But the balafon differs from the saron in two ways. First its bars are WOOD, not bronze, giving a warmer, woodier tone. Second, and beautifully, every bar has its OWN resonator: a gourd hung beneath it whose air cavity is tuned to that bar's note, so it acts as a Helmholtz resonator (a bottle blown at just the right pitch) and swells that one note — exactly the job a marimba's metal tube does under each bar. And each gourd carries a small membrane over a side-hole that BUZZES sympathetically when the bar sounds, a built-in mirliton that adds the balafon's characteristic rasp, the same trick as the dizi's dimo. The balafon is ancient in West Africa — the Sosso Bala, a sacred balafon, is said to date from the thirteenth century — and it is a direct ancestor of the marimba, carried across the Atlantic and grown into the marimbas of Latin America.

Матеріали

6

Необхідні інструменти

3

You can swap these in

Can't get one of the materials? Swap it for an equivalent — these work just as well.

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...