МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗЕЛЕНЕ МАЙБУТНЄ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Building a Djembe — The West African Rope-Tuned Goblet Drum
Woody

Створено

Woody

3. липень 2026NO
0
0
0
0
0

Building a Djembe — The West African Rope-Tuned Goblet Drum

Build a djembe: a goblet-shaped wooden drum with a goat-skin head, tuned not by heat but by PULLING ropes tight in a diamond weave. Carve the body, mount the skin on rings, then rope it up and tune it. A serious maker build in the membrane drum and rope tensioning, giving three voices — bass, tone and slap — from one head.
Середній
Several hours over several sessions

Інструкції

1

A drum you tune with rope

The djembe is a goblet-shaped wooden drum with a goat-skin head. Instead of heating the skin to tune it, you pull ropes tight in a diamond weave — the tighter the rope, the higher and sharper the drum.
2

Carve the goblet body

Hollow a goblet-shaped body — a wide bowl at the top narrowing to a stem and opening out at the foot. Traditionally it is carved from a single log; built up from wood, keep the bore smooth and the bottom fully open.

Матеріали для цього кроку:

Dry Softwood BoardDry Softwood Board1 штука
PVA Wood GluePVA Wood Glue1 штука

Необхідні інструменти ({count})

Sloyd Carving KnifeSloyd Carving Knife
HacksawHacksaw
3

Cut the head

Cut a round goat-skin rawhide head a good bit wider than the drum's bowl, with the hair scraped off.

Матеріали для цього кроку:

RawhideRawhide1 штука
4

Make two rings

Bend two metal rings that fit the drum's rim. Wrap one in the skin (the flesh ring) and leave one as a bottom ring; rows of rope loops hang from each.

Матеріали для цього кроку:

Bronze WireBronze Wire1 штука
Abaca Tying TwineAbaca Tying Twine1 штука
5

Mount the skin

Soak the skin, fold it over the top ring, and seat both over the bowl so the wet head lies across the mouth of the drum.
6

Rope it up

Lace a long rope up and down between the top ring's loops and the bottom ring, pulling the head down. Let it dry, then weave the verticals together in diamonds to pull them tighter still.

Матеріали для цього кроку:

Abaca Tying TwineAbaca Tying Twine1 штука
7

Tune and play

Pull more diamonds to tighten the head and raise the pitch. Then play bare-handed: a deep BASS in the centre, a ringing TONE on the edge, and a sharp cracking SLAP with loose fingers on the rim.
8

Compendium — three voices and a tuning rope

The djembe is a goblet membrane drum, close kin to the darbuka, but two things set it apart. First, its body is a big carved WOODEN goblet, not clay: struck in the centre the head drives a slow pulse of air down the hollow stem and out of the open foot, which acts as a horn to boom the deep BASS; struck near the rim the edge of the skin snaps for a ringing TONE, and a loose, cracking hit gives the bright SLAP — three distinct voices from one head, the palette of West African drumming. Second, and cleverest, is how it is tuned. A drumhead's pitch rises with tension, and where the darbuka's skin is glued or warmed, the djembe's is pulled tight by ROPE: the head is trapped between two metal rings, and a long rope laced between them and then woven into diamonds draws the rings together and stretches the skin — pull more diamonds and the whole head tightens and the drum sings higher, all with no heat and no glue, tunable in a moment and re-tunable forever. This rope-lacing is the same idea that tunes the Korean janggu, and the djembe's goblet shape is the wooden cousin of the clay darbuka. Carved by the blacksmith-craftsmen of the Mande peoples for many centuries, the djembe is said to 'gather everyone in peace'.

Матеріали

5

Необхідні інструменти

2

You can swap these in

Can't get one of the materials? Swap it for an equivalent — these work just as well.

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...