Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Angle Grinder: Reversible, with a Hollow Arbour and a Top Arbour Lock (Turley, US 5,718,621)
Forge

Створено

Forge

9. листопад 2026NO
7
0
0
0
0

Angle Grinder: Reversible, with a Hollow Arbour and a Top Arbour Lock (Turley, US 5,718,621)

An angle grinder spins a disc at right angles to its motor: a bevel gear on the motor shaft turns a bevel gear on an upright arbour. E. M. Turley (US 5,718,621, 1998) makes the arbour hollow. A bolt runs down through it into a hexagonal coupling piece that drives the disc and clamps it against the arbour's flange, so the motor can run either way without loosening the disc. To change the disc, a sliding lock piece on top locks the arbour, opens a hole over the bolt head and switches the motor off in one move. Source: E. M. Turley, "Reversible Angle Grinder with Top Arbour Lock", US Patent 5,718,621 (filed 1996, granted 1998). Picture: its Fig. 1.
Просунутий
Unknown

Інструкції

1

Read Turley

"The angle grinder according to the preferred embodiment of the invention includes a reversible motor driving a hollow arbour via a right angle bevel gear arrangement. The arbour has a right angle flange at its bottom. The flange abuts against one side of the disk tool."
2

Turn the hollow arbour

Turn an arbour hollow all through, with three outside shoulders (lower, middle and upper) for the two bearings and the bevel gear, and grooves above each for a snap ring. At the bottom, enlarge the bore into a hexagonal recess ending in a right-angle flange. At the top, enlarge the bore so the bolt head sits below the rim, and cut four equally spaced square notches (crenellations) in the rim. Sizes and metal are not given.

Матеріали для цього кроку:

Невідомий металНевідомий метал1 arbour

Необхідні інструменти ({count})

Токарний верстат по металуТокарний верстат по металу
Фрезерний верстатФрезерний верстат
Напилки (ручний напилок)Напилки (ручний напилок)
Невідомі розміриНевідомі розміри
3

Make the coupling piece and bolt

Make a coupling piece: a hexagonal upper part that fits the arbour's recess, a round pilot that fits the standard centre hole of commercial grinding discs, and a right-angle flange at its base. Bore and tap it from the top, closed at the bottom. Make a retaining bolt long enough to run from the arbour's top down into the coupling piece, threaded at its lower end (Fig. 1 draws a socket in its head).

Матеріали для цього кроку:

Невідомий металНевідомий метал1 coupling piece
Невідомий металНевідомий метал1 retaining bolt

Необхідні інструменти ({count})

Токарний верстат по металуТокарний верстат по металу
Фрезерний верстатФрезерний верстат
Набір мітчиків і плашокНабір мітчиків і плашок
Невідомі розміриНевідомі розміри
4

Cut the bevel gears

Cut two bevel gears with teeth at forty-five degrees (equal gears for a right-angle drive): one fixed on the arbour against its middle shoulder, one on the front end of the motor shaft. Tooth count and metal are not given.

Матеріали для цього кроку:

Невідомий металНевідомий метал2 bevel gears

Необхідні інструменти ({count})

Фрезерний верстатФрезерний верстат
Фреза для конічних колісФреза для конічних коліс
Невідомі розміриНевідомі розміри
5

Assemble the drive

Mount a reversible electric motor in the housing, its shaft running back in a rear bearing and forward in a front bearing, the bevel gear on its front end. Set the arbour upright in two bearings at its lower and upper shoulders, the bevel gears meshing, with snap rings above the bearings and the gear. Drop the bolt down the arbour on a lock washer, fit the coupling piece from below and screw it on. Motor rating, housing material and how the bearings are held are not given.

Матеріали для цього кроку:

ЕлектродвигунЕлектродвигун1 reversible
Кульковий підшипникКульковий підшипник4 штук
Невідомий матеріалНевідомий матеріал1 housing

Необхідні інструменти ({count})

Набір шестигранних ключівНабір шестигранних ключів
Невідомий спосіб формуванняНевідомий спосіб формування
Невідомі розміриНевідомі розміри
6

Fit the arbour lock

Make a rectangular lock piece that slides in the housing top across the arbour head, with a lever up through a slot in the housing, a tool hole, and a square tang underneath that drops into a rim notch. A spring on its front face holds it back in the running position. Fix a two-contact power switch to its rear so the motor circuit is broken when the piece is slid into the locking position. Cut a hole in the housing top over the bolt head and a slot for the lever.

Матеріали для цього кроку:

Невідомий металНевідомий метал1 lock piece
ПружинаПружина1 штука
Вимикач живленняВимикач живлення1 штука

Необхідні інструменти ({count})

Фрезерний верстатФрезерний верстат
Свердлильний верстатСвердлильний верстат
Набір сверделНабір свердел
Напилки (ручний напилок)Напилки (ручний напилок)
7

Change a disc

Push the lever forward: the tang locks the arbour, the switch cuts the motor and the tool hole sits over the bolt head. Unscrew the bolt from above with the key and pull the coupling piece; put the new disc on its pilot and screw it back up tight, so the disc is clamped between the arbour flange and the coupling flange. Let the lever spring back to run. Turley: a loose bolt cannot drop the disc, which rattles to warn you to tighten it.

Необхідні інструменти ({count})

Набір шестигранних ключівНабір шестигранних ключів

Матеріали

6

Необхідні інструменти

10

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...