Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО

Set-Wing Dasher Churn: Wings on Two Cross Rods Through the Staff Are Set by Screws to Lift or Press the Cream
William F. Armstrong and Morgan Payne of Cardington, Ohio, received US 32,814, dated 16 July 1861, for a dasher made of a staff pierced at right angles by two rods, each carrying a wing at either end. Each wing turns on its rod and is fixed by a set screw, so some can be set to lift the cream and others to press it down, and the angles changed at will. Upright strips inside the churn break the swirl.
The patent gives no sizes; every size here is ours.
Початківець
About 1 day
Інструкції
1
1
Setting the wings
Setting the wings
Завантаження блокнота Jupyter…
2
2
Paddles sloping opposite ways, five months before
Paddles sloping opposite ways, five months before
Mickey fixes his paddles' slopes. Armstrong and Payne let each wing be set by a screw.
3
3
Read US 32,814
Read US 32,814
"D, D, represent the dashers which are secured to the shafts C, C, by means of set screws as shown so that they may be made permanent in different positions when desired. The cream is elevated by some of the dashers and depressed by others, and the angle at which either occurs may be changed by setting the dashers in different positions."
4
4
Churn A and strips a
Churn A and strips a
Use a 20-litre food-grade bucket as the churn A. Cut four hardwood strips a 20 mm wide and 320 long, tapered behind so their faces stand upright 125 mm from the centre against the sloping wall, and screw them inside from outside a quarter turn apart, 20 mm above the floor, sealing the screw holes. Cut a 12 mm HDPE lid with a 27 mm hole in the middle.
Матеріали для цього кроку:
Відро на 20 літрів1 штука
Дошка з твердої деревини1 штука
Шурупи по дереву12 штук
Лист ПЕВГ1 штукаНеобхідні інструменти ({count})
Циркулярний верстат
Акумуляторний дриль
Набір свердел
Набір викруток
Компас
Електролобзик
Набір перових свердел5
5
Print the step
Print the step
The step on the floor: 40 mm across, 12 high, with a 12.8 mm hole 8 deep. PETG, 0.2 mm layers, 30 % infill, 4 walls.
6
6
Print the wings D (four)
Print the wings D (four)
A wing: 90 x 60 x 12 mm with a hub 22 mm across, bored 12.4 mm along its length for the rod and 5.2 mm across the hub for an M5 set screw. Print four. PETG, 0.2 mm layers, 30 % infill, 4 walls.
7
7
Staff B, rods C and wings D
Staff B, rods C and wings D
Plane a hardwood staff B 30 mm square and 325 mm long, with a 12 mm stainless pin 10 mm out of its foot, and turn its top 25 mm round for 45 mm above. Bore it 12.2 mm across 100 and 220 mm above its foot, the second at right angles to the first, and push a 12 mm stainless rod C 234 mm long through each. Slide a wing on each rod end and fix it with an M5 set screw: the lower pair turned 30 degrees one way, the upper pair 30 degrees the other. Pin a crank of mild steel flat bar, 108 mm throw, with a hardwood handle on the staff's top.
Матеріали для цього кроку:
Дошка з твердої деревини1 штука
Пруток із нержавкої сталі2 штук
Філамент PETG1 штука
Машинні гвинти4 штук
Смуга з маловуглецевої сталі1 штука
Шканти з твердої деревини1 штука
Шплінт1 штукаНеобхідні інструменти ({count})
3D-принтер FDM
Циркулярний верстат
Токарний верстат по дереву
Акумуляторний дриль
Набір свердел
Ножівка по металу
Напилки (ручний напилок)
Набір викруток8
8
The build in 3D
The build in 3D
FreeCAD model of this build, the bucket cut open: four upright strips, the staff on its step with two cross rods and four wings set at opposite angles, the lid and the crank.
9
9
Churn
Churn
Pour about 12 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket, set the dasher's pin in the step and put on the lid. Turn the crank steadily, timing it. If the cream climbs too high or sits too still, loosen the set screws and change the wings' angles. When the butter comes, lift out the dasher, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
Матеріали для цього кроку:
Жирні вершки12 l
Крупна морська сіль1 штука
Вода1 штукаНеобхідні інструменти ({count})
Термометр зі щупом, що лишається в страві
Секундомір
Цифрові кухонні ваги
Велика миска з нержавкої сталі
Набір викруток10
10
Troubleshooting
Troubleshooting
Set-wing churn troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**Wm. F. Armstrong** and **Morgan Payne** of Cardington, Morrow County, Ohio, US 32,814, 16 July 1861, "Churn". They claimed "the peculiar arrangement of the dashers or wings upon the shafts C, C". They do not say how the staff is worked; their drawing shows it stepped on a pin in the bottom, so ours is turned by a crank on its top. Their churn widened toward the bottom; ours, a bucket, widens toward the top. The patent gives no sizes; every size here is ours.
Матеріали
14- 1 штукаЗаповнювач
- 1 штукаЗаповнювач
- 12 штукЗаповнювач
- 1 штукаЗаповнювач
- 1 штукаЗаповнювач
- Заповнювач
- 1 штукаЗаповнювач
- 4 штукЗаповнювач
- 1 штукаЗаповнювач
- 1 штукаЗаповнювач
- 1 штукаЗаповнювач
- 12 lЗаповнювач
- 1 штукаЗаповнювач
- 1 штукаЗаповнювач
Необхідні інструменти
15- 1 vendor sell this, none ship to you yetЗаповнювач
- 1 vendor sell this, none ship to you yetЗаповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- 1 vendor sell this, none ship to you yetЗаповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
Файли дизайну
3За цим кресленням виготовляють
Пов'язані креслення
Ці креслення діляться знаннями — техніки, матеріали або принципи

Opposed Perforated-Paddle Churn: Sloping Holed Paddles on a Geared Shaft Pass Between Paddles Sloping the Other Way on Slide Bars
від Buttercup
Деревообробка
6
0
0
0
0
0

Notched-Rib Churn: A Solid S-Winged Dasher Turns Inside Upright Ribs Whose Notches Alternate, Crossing the Cream's Currents
від Buttercup
Деревообробка
7
0
0
0
0
0

Spiral-Flange Perforated Dasher Churn: Curved Holed Dashers Fling the Cream Out, a Spiral Flange With Vanes Drives It Back Down
від Buttercup
Деревообробка
10
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
від TheChef
РЕМЕСЛО
63
0
0
0
0
0
CC0 Суспільне надбання
Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.
Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

