Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Bathroom Scale: Four Flat Load Cells Between Two Plates (Angel, 1991)
Penny

Створено

Penny

2. листопад 2026DK
12
0
0
0
0

Bathroom Scale: Four Flat Load Cells Between Two Plates (Angel, 1991)

A floor scale only as thick as two plates. Four flat load cells sit in the corners between a base and a top plate; their strain gauges are wired into one bridge, so the signal is the sum of the four loads wherever you stand. Result: a low digital bathroom scale reading in pounds or kilograms. The patent gives under 0.05 % non-linearity, hysteresis and non-repeatability, and under 0.1 % error from off-centre loads; its feet let it stand on thick carpet. Source: S. Angel, US Patent 4,993,506 (1991). Unknown: the plate material and size, the maximum load, and the circuit. Ours: ebonite for the hard rubber, epoxy, the amplifier and display parts. Picture: patent drawing (Fig. 5).
Просунутий
2 days

Інструкції

1

Mount the four load cells

Put one load cell in each corner of the rigid base plate. Screw each one down to small flat raised pads on the plate. Place the pads away from the edge of the cell's beam, so that fixing the cell does not change its sensitivity. Under each cell, tap two holes through the base for the overload screws. Not given: the plate material and size.

Матеріали для цього кроку:

ТензодатчикТензодатчик4 штук
Основа й верхня плита вагОснова й верхня плита ваг1 base and top plate
Машинні гвинтиМашинні гвинти8 cell screws

Необхідні інструменти ({count})

Набір мітчиків і плашокНабір мітчиків і плашок
Набір викрутокНабір викруток
Невідомі розміриНевідомі розміри
2

Wire one bridge and the readout

Each cell's two gauges are half a Wheatstone bridge. Join the four halves into one full bridge, one half at each corner, so the bridge gives a signal in step with the sum of the four loads. The signal is amplified, turned into numbers by an analog-to-digital converter, worked into pounds or kilograms and shown on a display. Put the electronics and batteries in the space between the plates. Not given: the circuit. Ours: an op-amp and a segment LCD.

Матеріали для цього кроку:

Мікросхема операційного підсилювачаМікросхема операційного підсилювача1 amplifier
Аналого-цифровий перетворювачАналого-цифровий перетворювач1 штука
Сегментний РК-індикаторСегментний РК-індикатор1 штука
АкумуляторАкумулятор1 as the circuit needs
Монтажний провідМонтажний провід1 as needed
Дріт припоюДріт припою1 a little

Необхідні інструменти ({count})

ПаяльникПаяльник
3

Fit the top plate on hard rubber pads

Glue four flat round pads of a rigid but slightly yielding material, such as hard rubber, under the top plate. Give each pad small round studs that snap into the two load holes of its cell, so the weight goes in at the centres of those holes. The pads soften impacts when something is dropped on the scale and take up sideways forces as the top plate bends. The snaps let the top plate be pulled off for repairs. Ours: ebonite and epoxy.

Матеріали для цього кроку:

Ебонітовий стриженьЕбонітовий стрижень1 four pads
Двокомпонентна епоксидкаДвокомпонентна епоксидка1 a little

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
4

Fit the feet

Under the base, below each cell, fix a shallow foot of flexible material such as hard rubber, rounded underneath. Put its lowest point exactly below the centre of the cell's beam: the floor then pushes up at the beam's centre without bending it, and the scale works on thick carpet or uneven floors. Ours: ebonite.

Матеріали для цього кроку:

Ебонітовий стриженьЕбонітовий стрижень1 four feet
Двокомпонентна епоксидкаДвокомпонентна епоксидка1 a little

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
5

Set the overload stops

Load the scale to its maximum capacity. Turn the short screws in from below until they just touch the arms of each cell's loading element, then lock them with adhesive. Any heavier load now rests on the screws instead of bending the cells further. Not given: the maximum capacity. Ours: calibration weights and epoxy.

Матеріали для цього кроку:

Машинні гвинтиМашинні гвинти8 overload screws
Двокомпонентна епоксидкаДвокомпонентна епоксидка1 a little

Необхідні інструменти ({count})

Набір калібрувальних гирНабір калібрувальних гир
Набір викрутокНабір викруток

Матеріали

11

Необхідні інструменти

6

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...