Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Belt Sander: a Lathe-Driven Garnet-Belt Sander (Shop Notes, 1919)
Woody

Створено

Woody

4. листопад 2026NO
11
0
0
0
0

Belt Sander: a Lathe-Driven Garnet-Belt Sander (Shop Notes, 1919)

A shop belt sander for dressing wood surfaces: a 6 in garnet-paper belt running over four crowned wooden pulleys, one driven by the lathe, pressed down onto the work with a hand float. Best belt speed about 2,500 ft per minute; leave about 1 in between work and belt. Source: Popular Mechanics Shop Notes for 1919, p. 3235. Picture: the article's drawing.
Середній
Unknown

Інструкції

1

Turn the pulleys

Build up four solid wood pulleys 10 in across with 8 in faces and turn them in the lathe with a very slight crown; too much crown harms the belt.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини4 built-up pulleys

Необхідні інструменти ({count})

Токарний верстат по деревуТокарний верстат по дереву
2

Mount the pulleys

Mount one pulley on a firmly held arbor in the lathe and the other three on iron-pipe shafts on a frame (drawing). Turn and file a true journal on each pipe, pour babbitt bushings in the pulleys, and cut oil grooves in the pipe or babbitt. Supporting the shafts on one side lets the belt slip off; supporting both sides is stronger.

Матеріали для цього кроку:

Сталева труба (товстостінна, з різьбовими кінцями)Сталева труба (товстостінна, з різьбовими кінцями)3 shafts
Невідомий металНевідомий метал1 babbitt bushings
Сосновий пиломатеріалСосновий пиломатеріал1 frame

Необхідні інструменти ({count})

Напилок по металуНапилок по металу
Дірчаста шумівкаДірчаста шумівка
Ручна пилкаРучна пилка
МолотокМолоток
3

Make the belt

Cut 6 in garnet paper (No. 1 1/2 for general work) so the ends just meet over the pulleys. Glue the smooth side at the joint, splice it with a strip of cloth about 1 in wide and then one about 3 in wide, cover each side with paper, and clamp between two small boards.

Матеріали для цього кроку:

Наждачний папірНаждачний папір1 6 in garnet paper
Бавовняна тканинаБавовняна тканина1 штука
Тваринний клейТваринний клей1 штука

Необхідні інструменти ({count})

Струбцина типу CСтрубцина типу C
4

Set up and run

Run the belt at about 2,500 ft per minute using the lathe's cone pulley. Set the work about 1 in below the belt on a table or a low sliding platform (two sets of tongue-and-groove joints at right angles), start the machine and press the belt down with a float like a blackboard eraser, or a roller.

Матеріали для цього кроку:

Сосновий пиломатеріалСосновий пиломатеріал1 platform, float

Необхідні інструменти ({count})

Токарний верстат по деревуТокарний верстат по дереву

Матеріали

7

Необхідні інструменти

6

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...