Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО

Bench Glassblowing Torch: Brass Gas Blowpipe with a Glass Air Jet (Shenstone, 1916)
A glassblower's gas blowpipe you can make yourself: a brass tube with a side tube for gas, and a glass air jet down its middle fed from a foot-blower. A fine jet gives the small pointed flame for joints, and a wider jet the big brush flame for heating large tubes. It is pegged into a wooden block on a sheet-iron-covered bench, with taps for gas and air at the bench edge.
Result: a bench blowpipe for working glass tube. Make two: one about 11 mm bore for small work, one 15 to 17 mm for large.
Source: W. A. Shenstone, The Methods of Glass-Blowing (1916), pp. 3-9. Unknown: the brazing metal and the tap type. Picture: Fig. 1 of the book.
Середній
Unknown
Інструкції
1
1
Braze the gas inlet
Braze the gas inlet
Take a brass tube for the body: about 11 mm bore for the small blowpipe, 15 to 17 mm for the large one. Braze a side tube for the gas onto it 10 to 12 cm from the back end, according to the tube's size. Fix a spike to it for mounting. Ours: borax as the flux. Not given: the brazing metal.
Матеріали для цього кроку:
Латунна трубка1 body and side tube
Невідомий метал1 brazing metal and spike
Порошок бури1 brazing fluxНеобхідні інструменти ({count})
Ножівка по металу
Горно2
2
Fit the glass air jet
Fit the glass air jet
Fit a glass tube down the middle of the brass tube, held by a cork at the back end, its tip near the mouth. For the small pointed flame, draw the tip down to the size of a large knitting needle. For a large flame rich in air, the tip may be nearly half the bore of the brass tube. Make several air tubes of different sizes for each blowpipe.
Матеріали для цього кроку:
Скляна трубка3 air jets of several sizes
Корки1 jet corkНеобхідні інструменти ({count})
Пальник Бунзена3
3
Set up the bench
Set up the bench
Cover the bench round the blowpipe with sheet iron. Drill several holes in a block of wood so the spike can be set at different positions. Fix two taps near the bench edge, one for gas and one for air. Connect them by flexible tubes to the supplies on one side and to the blowpipe's gas inlet and air jet on the other. Ours: mild steel sheet, rubber tubing. Not given: the tap type.
Матеріали для цього кроку:
Лист маловуглецевої сталі1 bench cover
Брусок твердої деревини1 mounting block
Невідомий вентиль2 gas and air taps
Гумова трубка1 flexible tubesНеобхідні інструменти ({count})
Свердлильний верстат4
4
Light it and blow
Light it and blow
Light the gas at the mouth and work a foot-blower to drive air through the glass jet into the burning gas. Little air and a small jet give the pointed flame; plenty of gas and a strong blast give the large, non-luminous brush flame.
Необхідні інструменти ({count})
Ковальський міхМатеріали
9- 1 body and side tubeЗаповнювач
- 1 brazing metal and spikeЗаповнювач
- 1 brazing fluxЗаповнювач
- 3 air jets of several sizesЗаповнювач
- 1 jet corkЗаповнювач
- 1 bench coverЗаповнювач
- 1 mounting blockЗаповнювач
- 2 gas and air tapsЗаповнювач
- 1 flexible tubesЗаповнювач
Необхідні інструменти
5- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
Матеріали з пов'язаних креслень

10% атрибуція
Venetian Borax: Refining Tincal with Lime
від Charlie
неорганічні
22
0
0
0
1
0

10% атрибуція
Natural Rubber Tubing, Bands and Sheet: Sulfur-Cured with Heat
від Mary
Хімія
16
0
0
0
2
0

10% атрибуція
Oak Boards and Blocks, Milled and Air-Dried
від Woody
Деревообробка
45
0
0
0
3
0

10% атрибуція
Building a Box Bellows — The Breath That Makes Metal Obey Fire
від Emma
Деревообробка
108
0
0
0
8
0
За цим кресленням виготовляють
CC0 Суспільне надбання
Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.
Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.
