Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Blake Jaw Breaker: Eccentric, Pitman and Two Toggles Swing a Steel Jaw Against a Fixed Chilled Plate (Richards, Ore Dressing, 1903)
Forge

Створено

Forge

15. листопад 2026NO
4
0
0
0
0

Blake Jaw Breaker: Eccentric, Pitman and Two Toggles Swing a Steel Jaw Against a Fixed Chilled Plate (Richards, Ore Dressing, 1903)

Eli Whitney Blake's jaw breaker (patented 1858), the standard first crusher of the ore mill, as Robert Richards described it: a ribbed cast frame on four legs, a fixed jaw bedded in zinc, a steel swing jaw hung from a shaft at the top, and an eccentric that lifts a pitman to straighten two toggles and push the jaw shut; rubber springs pull it back. A wedge sets the gap; a heavy flywheel carries it through each half-turn of crushing.
Просунутий
Weeks (castings and machining)

Інструкції

1

Sizes and power

Завантаження блокнота Jupyter…
2

Read Richards

"As the eccentric lifts the pitman, it straightens out the toggles, lengthening the distance between their outer ends. This forces the swing jaw to approach the fixed jaw, crushing the rock."
3

Frame and fixed jaw

Cast the frame of strong, ribbed cast iron or cast steel, with four legs bolted down, bearing boxes on top for the swing-jaw shaft and the eccentric shaft, and a horizontal web at the rear for the toggle block and wedge. Bed the fixed jaw against the frame end with 1/4 in. (6 mm) of zinc, and hold its jaw plate with two wedge-shaped cheek plates driven into recesses in the frame.

Матеріали для цього кроку:

Чавунні виливкиЧавунні виливки1 штука
Цинковий злитокЦинковий злиток1 штука
Набір шестигранних болтівНабір шестигранних болтів1 штука

Необхідні інструменти ({count})

Ливарний ківшЛиварний ківш
ПоліспастПоліспаст
МолотокМолоток
4

Swing jaw

Make the swing jaw of steel, fixed to its shaft by a gib and key bolt, with its jaw plate held by dovetails, a steel toggle bearing at the back and an eye near the bottom for the spring rod. Jaw plates: chilled cast iron with lengthwise 90° corrugations.

Матеріали для цього кроку:

Чавунні виливкиЧавунні виливки1 штука
Сталевий валСталевий вал1 штука

Необхідні інструменти ({count})

Токарний верстат по металуТокарний верстат по металу
Набір гайкових ключівНабір гайкових ключів
5

Pitman, toggles and wedge

Hang a strong steel pitman from the eccentric shaft on babbitt bearings taken up by a key. Fit two toggles: one between the toggle block and the pitman, one between the pitman and the swing jaw, all four toggle bearings steel, held by set screws. Set the toggle block on its bolt against the wedge, which an adjusting bolt raises or lowers.

Матеріали для цього кроку:

Сталевий валСталевий вал1 штука
Невідомий металНевідомий метал1 штука
Чавунні виливкиЧавунні виливки1 штука

Необхідні інструменти ({count})

Токарний верстат по металуТокарний верстат по металу
Набір гайкових ключівНабір гайкових ключів
6

Springs, flywheel and drive

Fit two spring rods from the swing jaw through rubber springs held in compression against a spring bar. Key a heavy flywheel to the eccentric shaft and bolt the drive pulley to it; plug all oil holes against grit and shield the boxes and toggles with the half hopper. Drive it by belt (Table 5: 275 rev./min).

Матеріали для цього кроку:

Аркуш натурального каучукуАркуш натурального каучуку1 штука
Чавунні виливкиЧавунні виливки1 штука
БлокБлок1 штука
Приводний пасПриводний пас1 штука
Набір шестигранних болтівНабір шестигранних болтів1 штука

Необхідні інструменти ({count})

Набір гайкових ключівНабір гайкових ключів
Токарний верстат по металуТокарний верстат по металу
7

Run and adjust

Feed rock by hand, shovel or chute into the mouth. As the jaw plates wear and the product gets coarse, raise the wedge by its nut; when that is used up, fit longer toggles that keep the pitman vertical; then turn the jaw plates end for end; last, fit new plates.

Необхідні інструменти ({count})

Набір гайкових ключівНабір гайкових ключів
8

Troubleshooting

Jaw breaker troubleshooting.

Flow

Loading...
9

History and honest limits

From Robert H. Richards, *Ore Dressing* vol. I (1903), Chapter II, §§ 11-14, pp. 13-17, Figs. 5-8 and Table 5 (checked on the archive.org scan oredressing01richuoft; p. 15 from its text layer). Blake's first 1858 form gave the most movement at the mouth; he soon reversed it so the bottom of the jaw moves most. Richards describes a bought Farrel or Fraser & Chalmers machine: building it from castings and metric figures are ours, and the babbitt alloy has no head yet.

Матеріали

8

Необхідні інструменти

5

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...