Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Knock-Down Footstool: Bolted Metal Legs and Rails Under a Screwed-On Wooden Top (Bolens, 1900)
Forge

Створено

Forge

13. листопад 2026NO
6
0
0
0
0

Knock-Down Footstool: Bolted Metal Legs and Rails Under a Screwed-On Wooden Top (Bolens, 1900)

Harry W. Bolens of Port Washington, Wisconsin, received US 640,265, dated 2 January 1900, for a footstool whose base comes apart: four metal corner legs and four rails bolted together, with a wooden top screwed on through lugs on the legs. It packs flat for storage and shipping. His legs were ornamental castings; ours are bent from steel angle. All sizes are ours.
Початківець
About 4 hours

Інструкції

1

Cut list

Завантаження блокнота Jupyter…
2

Read US 640,265

"The above-described base has the advantage of being a knockdown structure, and thus I provide for economical storage and transportation."
3

Make the legs

Cut four legs of steel angle to the notebook's length, his corner legs A. At the top of each, cut and bend a small tab inward to make the flange and lug (his b and c), and drill the lug for a top screw. File off sharp edges.

Матеріали для цього кроку:

Кутник із м'якої сталіКутник із м'якої сталі1 штука

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Слюсарні лещатаСлюсарні лещата
Слюсарний молоток із кульковим бойкомСлюсарний молоток із кульковим бойком
Свердлильний верстатСвердлильний верстат
Набір сверделНабір свердел
Набір напилківНабір напилків
4

Make the rails

Cut two side rails and two end rails of flat bar, his rails B. Bend each end slightly (his offset ends) so it lies flush inside the leg's angle. Drill matching holes through rail ends and legs.

Матеріали для цього кроку:

Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Слюсарні лещатаСлюсарні лещата
Свердлильний верстатСвердлильний верстат
Набір сверделНабір свердел
5

Bolt the base

Bolt each rail end to its leg with a bolt and nut, his bolts f and nuts g. Check the base stands square and level.

Матеріали для цього кроку:

Набір шестигранних болтівНабір шестигранних болтів1 штука

Необхідні інструменти ({count})

Розвідний ключРозвідний ключ
6

Fit the top

Cut and sand a hardwood top, his top C. Set it on the base and drive a screw up through each leg's lug into it, his screws h. Upholster it if you like, as he allows.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Шурупи по деревуШурупи по дереву1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Наждачний папірНаждачний папір
Набір викрутокНабір викруток
7

Troubleshooting

Footstool troubleshooting.

Flow

Loading...
8

History and honest limits

**Harry W. Bolens** of Port Washington, Wisconsin, US 640,265, dated 2 January 1900, filed 4 October 1899. He claimed "a footstool-base consisting of legs provided at their upper ends with inwardly-extending flanges as well as horizontal lugs ... apertured for the engagement of top securing devices" and rails between the flanges. His legs and rails were castings, though he does not limit the material; the steel angle and flat bar, the bent lugs, the hardwood top and all sizes are ours.

Матеріали

5

Необхідні інструменти

10

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...