Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО

Boring Bar: Driven Between Centres, with a Set-Screw Cutter (Yates, 1922)
A home-made boring bar for holes too long for an ordinary boring tool, which would spring. A short, stiff bar runs between the lathe centres, driven by a dog, and carries a hardened tool-steel cutter locked in a cross-hole by a set screw. The work is bolted to the lathe carriage and fed past the turning cutter.
Result: a boring bar, plus the small short-cut bar of Fig. 110.
Source: R. F. Yates, Lathe Work for Beginners (1922), pp. 134-136. Unknown: bar diameter and set-screw size. Picture: Figs. 110-111 of the book.
Середній
Unknown
Інструкції
1
1
Turn the bar
Turn the bar
Turn a bar no longer than the job needs; the shorter it is, the less it twists under the cut. Drill both ends for the lathe centres. For short cuts, the small bar of Fig. 110 is 4 to 6 inches long with a round shank and a squared end. Ours: mild steel round bar. Not given: the diameter.
Матеріали для цього кроку:
Круглий пруток з маловуглецевої сталі1 boring barНеобхідні інструменти ({count})
Токарний верстат по металу
Невідомі розміри2
2
Fit the cutter and set screw
Fit the cutter and set screw
Drill a cross-hole through the bar for the cutter and drill and tap a hole into it for a set screw that locks the cutter. Make the cutter of tool steel, grind its point with proper clearance, and harden it.
Матеріали для цього кроку:
Квадрат з інструментальної сталі1 cutter
Невідомий метал1 set screwНеобхідні інструменти ({count})
Свердлильний верстат
Набір мітчиків і плашок
Точильний круг
Піч для термообробки
Гартівна діжка3
3
Bore with it
Bore with it
Bolt the work down to the lathe carriage carefully and securely; carriage bolts of several sizes are handy for this. Drive the bar between centres with a dog and feed the carriage. Run very slowly when boring cast iron, and keep the feed light so the bar does not spring.
Необхідні інструменти ({count})
Токарний верстат по металу
Болт із півкруглою головкоюМатеріали
3- 1 boring barЗаповнювач
- 1 cutterЗаповнювач
- 1 set screwЗаповнювач
Необхідні інструменти
8- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
Матеріали з пов'язаних креслень

10% атрибуція
Mild Steel Bar Stock Forged from an Ingot
від Forge
Сучасний
44
0
0
0
5
0

10% атрибуція
Tool-Steel Bar: Crucible Steel Drawn Out at a Cherry-Red Heat
від Forge
Коваль
32
0
0
0
5
0

10% атрибуція
Lathe Cutting Tool: Ground to the Clearance and Slope for Each Metal (Machinery's Handbook, 1924)
від Forge
Металообробний інструмент
12
0
0
0
1
0
За цим кресленням виготовляють
CC0 Суспільне надбання
Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.
Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.
