Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Five-Foot Bait-Casting Rod: Hand-Tapered Dagame Stick, Cork Grasps and Agate Guides (Boy Mechanic, 1915)
Woody

Створено

Woody

13. листопад 2026NO
5
0
0
0
0

Five-Foot Bait-Casting Rod: Hand-Tapered Dagame Stick, Cork Grasps and Agate Guides (Boy Mechanic, 1915)

Stillman Taylor's first rod for a beginner, from The Boy Mechanic, Book 2 (1915): a one-piece 5 ft bait-casting rod planed by hand from a 5/8 in square stick of dagame to his calipered taper (1/2 in at the grasp to 1/8 in at the tip), with a double cork grasp around the reel seat, two agate guides and an agate tip, whipped in silk and varnished. He made it with "a saw, plane, jackknife, file, and sandpaper".
Середній
About 2 weeks (glue and varnish drying)

Інструкції

1

Fig. 5: the taper, station by station

Завантаження блокнота Jupyter…
2

Read The Boy Mechanic, Book 2

"The short one-piece bait-casting rod with but one ferrule is the easiest rod to make." His materials: 1 dagame or greenheart stick, 5 ft long and 5/8 in square; 1 reel seat with straight hood, 3/4 in; 1 butt cap, 1 in; 1 taper, small end 15/32 in; 1 offset agate top, 3/32 in, and 2 narrow agate guides, 1/2 in, all in German silver; 2 doz. corks, 1-1/4 by 1-1/8 in; two 50 yd spools of silk, red and green, 00 size.
3

Make the gauge and grooved board

On a strip of paper draw the rod full length: a 1/2 in line for the butt, a centre line 60 in long, a 1/8 in line at the tip, and join the ends. From 12 in, mark a crossline every 6 in and write his diameters on them (see the notebook). File nine slots in a thin strip of brass to these diameters as a gauge. Plane a groove, gradually shallower toward one end, in a 5 ft tongue-and-groove pine board about 1 in thick, and nail it to the bench edge, groove up.

Матеріали для цього кроку:

Латунний листЛатунний лист1 штука
Соснова дошкаСоснова дошка1 штука
ЦвяхиЦвяхи1 штука

Необхідні інструменти ({count})

Пакувальний крафт-папірПакувальний крафт-папір
ОлівецьОлівець
Напилки (ручний напилок)Напилки (ручний напилок)
Слюсарні лещатаСлюсарні лещата
ШтангенциркульШтангенциркуль
Ручний рубанокРучний рубанок
МолотокМолоток
РулеткаРулетка
4

Plane the stick square and tapered

Plane along each side and from both ends of a 5/8 in square dagame strip to find the grain. Drill two holes about 1/4 in from the butt end and hook them over a brad in the bench corner, so you plane with the grain. Plane it straight and true to 1/2 in square, evenly from all sides, ignoring kinks. Knife-mark the hand grasp 12 in from the butt (11 in for a single grasp). Then plane an even taper from butt to tip, checking with caliper and gauge at every 6 in mark and planing the thick spots lightly. Bend the tip on the floor: if it stays bent, the wood needs a few weeks' seasoning in a warm place.

Матеріали для цього кроку:

Деревина дагамеДеревина дагаме1 штука
ЦвяхиЦвяхи1 штука

Необхідні інструменти ({count})

Ручний рубанокРучний рубанок
Обдирний стругОбдирний струг
Точильний каміньТочильний камінь
Ручний дрильРучний дриль
ШтангенциркульШтангенциркуль
Макетний ніжМакетний ніж
МолотокМолоток
5

Round the rod

Lay the rod in the grooved board, a corner up, and take each corner off with a finely set small plane to make it eight-sided, calipering every 6 in mark and keeping the eight sides even, until it is almost round and tapers evenly from the grasp mark to the tip. File grooves across the edge of a cabinetmaker's steel scraper with a round file, sharpen them, and scrape the rod perfectly round; sandpaper it smooth. Tie on the tip and guides and string the reel on to try a few casts, then smooth it with No. 0 sandpaper.

Матеріали для цього кроку:

Наждачний папірНаждачний папір1 штука

Необхідні інструменти ({count})

Обдирний стругОбдирний струг
Сталевий шкребокСталевий шкребок
Напилки (ручний напилок)Напилки (ручний напилок)
ШтангенциркульШтангенциркуль
6

Build the lower grasp and reel-seat sleeve

Cut a hole in the corks with a sharpened tube turned like a wad cutter. Cut the butt off square about 1 in from the end, to remove the holes. Glue on a cork with hot glue, then cork after cork, about 10, for a grasp a trifle over 5 in long. For the reel-seat sleeve, bore a 15/32 in hole through white pine about 3/4 in thick and 5 in long, plane the outside to slip inside the reel seat, taper one end to match it, and make it about 1/4 in shorter than the reel seat. Glue it down on top of the last cork and leave the glue a day or two.

Матеріали для цього кроку:

Коркові кільцяКоркові кільця10 штук
Тваринний клейТваринний клей1 штука
Соснова дошкаСоснова дошка1 штука

Необхідні інструменти ({count})

Латунна трубкаЛатунна трубка
Напилки (ручний напилок)Напилки (ручний напилок)
Ручна пилкаРучна пилка
Ручний дрильРучний дриль
Обдирний стругОбдирний струг
7

Fit the butt cap and reel seat

Trim the grasp to about 1-1/16 in diameter (1-1/4 in corks need little trimming), leaving the top cork as a shoulder, and fit the lower corks to the butt cap's taper. Heat the cap moderately, rub melted ferrule cement inside and force it on; when hard, drive a small brass pin or brad through and file it flush. Cut the 4-1/2 in reel seat down to 3-7/8 in and fit it with the hood at the lower end, worked into the cork for a tight joint. Cement the sleeve, push the reel seat home and drive a small pin through the hood into the wood a short way only, not through the rod.

Матеріали для цього кроку:

Затильник вудлищаЗатильник вудлища1 штука
КотушкотримачКотушкотримач1 штука
Клей для втулокКлей для втулок1 штука

Необхідні інструменти ({count})

Макетний ніжМакетний ніж
Напилки (ручний напилок)Напилки (ручний напилок)
Пропановий пальникПропановий пальник
МолотокМолоток
8

Build the upper grasp and finish the wood

Cement corks above the reel seat, the first pressed against the seat and turned so the metal enters it, then shape them into a smooth swelled grasp and cement on the winding check. Sand the rod, wet it to raise the grain, and sand again with old paper; for a finer polish rub with pumice and oil and an oiled rag. File the tip to fit the agate top, smear on melted ferrule cement and push the top home. Rub the wood over with a cloth wet with varnish to fill the pores, and wipe off the surplus.

Матеріали для цього кроку:

Коркові кільцяКоркові кільця6 штук
Тваринний клейТваринний клей1 штука
Закінчення руків'я (віндинг-чек)Закінчення руків'я (віндинг-чек)1 штука
Тюльпан вудлищаТюльпан вудлища1 штука
Клей для втулокКлей для втулок1 штука
Наждачний папірНаждачний папір1 штука
Каретний лакКаретний лак1 штука

Необхідні інструменти ({count})

Макетний ніжМакетний ніж
Напилки (ручний напилок)Напилки (ручний напилок)
Пропановий пальникПропановий пальник
9

Whip on the guides

Place the first guide 19-1/2 in from the metal taper above the upper grasp and the second 15-1/2 in further on; round the sharp edges of their bases with a fine file and hold them with a few turns of common thread. Whip with 00 silk using the invisible knot: tuck the end under the first coil, wind tightly by turning the rod, lay a waxed loop of silk about 4 in long under the last turns, wind about 1/8 in beyond the pointed flange, cut the silk and pull its end back under with the loop. About a dozen turns make a winding; edgings of three or four turns go on after, in red with green or yellow.

Матеріали для цього кроку:

Пропускне кільце вудлищаПропускне кільце вудлища2 штук
Шовк для обмотки вудлищШовк для обмотки вудлищ1 штука
Лляна ниткаЛляна нитка1 штука
Бджолиний віскБджолиний віск1 штука

Необхідні інструменти ({count})

Напилки (ручний напилок)Напилки (ручний напилок)
Макетний ніжМакетний ніж
10

Shellac and varnish

Clip any fuzzy ends and give the silk two light coats of white shellac dissolved in grain alcohol, warmed and laid on with a small camel's-hair brush; let it dry a couple of days. Warm the coach varnish in a pot of hot water for five minutes and brush it on evenly with a brush about 1/2 in wide, in a warm place (about 75 deg F). Hang the rod by the tip in a dust-free room; allow three days between coats; two coats protect it, three give complete protection.

Матеріали для цього кроку:

Шелаковий лакШелаковий лак1 штука
Каретний лакКаретний лак3 штук

Необхідні інструменти ({count})

Широкий малярний пензельШирокий малярний пензель
11

Troubleshooting

Casting rod troubleshooting.

Flow

Loading...
12

History and honest limits

From "Fishing-Rod Making and Angling, Part I -- A One-Piece Casting Rod" by Stillman Taylor, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 59-66). His text says about 10 corks for the lower grasp; his list allows 2 dozen for both grasps. The block plane, vernier caliper and other modern tool names, and the metric figures, are ours; his tools were "a saw, plane, jackknife, file, and sandpaper" plus those in his tools section.

Матеріали

18

Необхідні інструменти

17

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...