Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО

Leather Punch from an Old Pipe Nipple: Edge Ground Thin, Slug Slot Cut Above (Boy Mechanic, 1915)
A shop-made hollow punch for round holes in leather from The Boy Mechanic, Book 2 (1915): an old pipe nipple of the size you need, one end ground on the outside to a very thin cutting edge, and a small slot a little above it to push the leather slugs out.
Початківець
Half an hour
Інструкції
1
1
Read the tip
Read the tip
"The cutter end can be ground very thin to prevent an over-cut, while a small slot cut a little above it will allow the removal of the leather slugs."
2
2
Choose the pipe
Choose the pipe
Pick an old pipe nipple whose bore matches the hole you want: pieces of almost any size turn up around a shop. If the piece is long, saw it to a handy length (ours).
Матеріали для цього кроку:
Сталева труба (товстостінна, з різьбовими кінцями)1 штукаНеобхідні інструменти ({count})
Слюсарні лещата
Ножівка по металу3
3
Grind the cutter end
Grind the cutter end
Grind one end on the outside to a long bevel, leaving a very thin edge round the bore, as the hatched section in the sketch shows. Keep turning the pipe so the edge stays even.
Необхідні інструменти ({count})
Настільний точильний станок4
4
Cut the slug slot
Cut the slug slot
A little above the edge, cut a small slot through the wall (the sketch shows a triangle) to push the slugs out. Ours: drill a hole and file it to shape.
Необхідні інструменти ({count})
Слюсарні лещата
Свердлильний верстат
Напилки (ручний напилок)
Надфілі5
5
Punch
Punch
Ours: lay the leather on end-grain wood, stand the punch upright and strike the top with a mallet. Poke the slugs out through the slot.
Необхідні інструменти ({count})
Дерев'яний молоток (киянка)6
6
Troubleshooting
Troubleshooting
Punch troubleshooting.
Flow
Loading...
7
7
History and honest limits
History and honest limits
From "Pipe Used as a Leather Punch", **The Boy Mechanic, Book 2** (Popular Mechanics, 1915), p. 138 (checked on the archive.org scan boymechanicbook200chic2). The note gives no sizes; the way the slot is cut, the length and the striking method are ours.
Матеріали
1- Заповнювач
Необхідні інструменти
7- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
За цим кресленням виготовляють
Пов'язані креслення
Ці креслення діляться знаннями — техніки, матеріали або принципи
CC0 Суспільне надбання
Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.
Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.


