Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Ski Sled: Two 10 ft Ash Ski Runners With a Rocker, Under a Three-Board Top (Boy Mechanic, 1919)
Woody

Створено

Woody

13. листопад 2026NO
5
0
0
0
0

Ski Sled: Two 10 ft Ash Ski Runners With a Rocker, Under a Three-Board Top (Boy Mechanic, 1919)

George J. Egelberg's ski sled from The Boy Mechanic, Book 3 (1919): "built low and wide so that it will not tip easily", on two 10 ft by 6 in ash runners boiled and bent like skis, set on knee blocks with a slight rocker, and topped with three 6 in boards.
Середній
About 2 days

Інструкції

1

His sizes, and the rocker

Завантаження блокнота Jupyter…
2

Read The Boy Mechanic, Book 3

"The skis, or runners, are cut 10 ft. long and 6 in. wide, from 1-in. ash boards that are straight-grained."
3

Thin the bend

Cut two runners 10 ft long and 6 in wide from straight-grained 1 in ash. Where the curve will be, plane about 1/4 in off the upper side, but not at the very tip, so the skis bend more easily.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини2 штук

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Ручний рубанокРучний рубанок
РулеткаРулетка
ОлівецьОлівець
4

Boil and bend

If steaming is not handy, boil the skis with at least 1-1/2 ft of the points under water and the vessel covered so little steam escapes, for at least one hour. Take them out, put them side by side in the bending blocks at once and bend with slow, even pressure; weight the long ends and leave them 8 or 10 hours to dry. Sharpen the points after bending.

Матеріали для цього кроку:

Соснова дошкаСоснова дошка1 штука

Необхідні інструменти ({count})

Велика каструляВелика каструля
Струбцина з напрямноюСтрубцина з напрямною
Ручний рубанокРучний рубанок
5

Set the blocks and top

For a slight rocker, make the centre knee block 6 in high and the two end blocks 5-1/2 in. Run a 1/4 in flat-head bolt through the ski, the block and the cross strip, countersinking the heads in the running surface. Make the top of three 6 in boards fastened to the crosspieces, and brace the ski tips with a 2 in strip.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Соснова дошкаСоснова дошка3 штук
Болт із півкруглою головкоюБолт із півкруглою головкою6 штук
Плоска шайбаПлоска шайба6 штук
Шурупи по деревуШурупи по дереву1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Ручний дрильРучний дриль
Набір зенківокНабір зенківок
МолотокМолоток
6

Troubleshooting

Ski sled troubleshooting.

Flow

Loading...
7

History and honest limits

From "A Ski Sled" by George J. Egelberg, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, p. 41). The bending-block shape and knee pieces come from his drawing. The tools and metric figures are ours.

Матеріали

5

Необхідні інструменти

9

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...