Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Straight-Sided Guitar: Maple Box, Pine Top, Hatpin Frets and a 24-Inch Scale (Boy Mechanic, 1913)
Woody

Створено

Woody

13. листопад 2026NO
7
0
0
0
0

Straight-Sided Guitar: Maple Box, Pine Top, Hatpin Frets and a 24-Inch Scale (Boy Mechanic, 1913)

A six-string guitar "having straight lines, giving it an old-fashioned appearance", from The Boy Mechanic (1913): a tapered box of hard maple with a seasoned soft-pine top, a drawknifed neck, frets cut from hatpins and a 24 in scale. Sizes are read on the 1913 scan. "If care is taken in selecting the material, and having it thoroughly seasoned, the finished instrument will have a fine tone."
Просунутий
About 1 week, with glue drying

Інструкції

1

Cutting list and frets

Завантаження блокнота Jupyter…
2

Read The Boy Mechanic

"The sides, ends and bottom are made of hard wood, preferably hard maple, and the top should be made of a thoroughly seasoned piece of soft pine." (J. H. Stoddard, Carbondale, Pa.)
3

Cut the pieces

Cut from thoroughly seasoned wood: top 3/16 by 14 by 17 in (soft pine); bottom 3/16 by 14 by 17 in, two sides 3/16 by 3-5/8 by 16-3/4 in, and ends 3/16 by 3-5/8 by 13-1/8 in and 9-5/8 in (hard maple); neck 1 by 2-5/16 by 18-1/2 in; fingerboard 3/16 by 2-5/8 by 16 in.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Соснова дошкаСоснова дошка1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
РулеткаРулетка
Столярний косинецьСтолярний косинець
4

Shape the neck and fingerboard

Taper the neck from G to F and from J to F, with the back rounded, using a drawknife: 2-3/8 in at the heel, 1-7/8 in at the nut F, and a head 2-3/4 in wide and 6-1/2 in long. Taper the fingerboard to match. Glue a piece of hard wood 1/4 in square and 1-7/8 in long across the neck at F as the nut. Glue the fingerboard to the neck and clamp it until the glue sets.

Матеріали для цього кроку:

Смуга твердої деревиниСмуга твердої деревини1 штука
Столярний клейСтолярний клей1 штука

Необхідні інструменти ({count})

СкобельСкобель
Ручна пилкаРучна пилка
Струбцина з напрямноюСтрубцина з напрямною
5

Fret the fingerboard

Mark the frets from the nut using the computed positions in step 1 (fret 1 at 1.347 in, fret 12 at 12 in). His drawing gives only five spaces, 1-2/5, 1-3/16, 1-1/8, 1-1/16 and 1 in; added up they put the 5th fret about 0.3 in short of the true place, so they are shown for history only. Cut pieces from hatpins and fasten them across the fingerboard with small wire staples. Mark accurately: the frets decide the pitch.

Матеріали для цього кроку:

Капелюшна шпилькаКапелюшна шпилька1 штука
Дротяна скобаДротяна скоба1 штука

Необхідні інструменти ({count})

ПлоскогубціПлоскогубці
МолотокМолоток
РулеткаРулетка
Столярний косинецьСтолярний косинець
6

Build the box

Glue the sides and ends together, so the body is 10 in wide at the neck end, 13-1/2 in at the tail and 16-1/2 in long. Glue the front on, put heavy weights on top and give the glue time to dry. Fasten pieces of soft wood in the corners as braces, glue a small block C inside the neck end to take the bolt, and glue strips of soft wood K across the front and back to strengthen them. Cut the sound hole in the top as drawn.

Матеріали для цього кроку:

Хвойний брусок (рейка)Хвойний брусок (рейка)1 штука
Столярний клейСтолярний клей1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Струбцина з напрямноюСтрубцина з напрямною
Коловорот із перкоюКоловорот із перкою
7

Fit the neck

Make the brace D 1 in thick, to any shape you like. Glue the neck to the box and secure it with a carriage bolt at A through the end and block C. Glue the back on and smooth the outside with sandpaper.

Матеріали для цього кроку:

Смуга твердої деревиниСмуга твердої деревини1 штука
Болт із півкруглою головкоюБолт із півкруглою головкою1 штука
Дошка з твердої деревиниДошка з твердої деревини1 штука
Столярний клейСтолярний клей1 штука
Наждачний папірНаждачний папір1 штука

Необхідні інструменти ({count})

Коловорот із перкоюКоловорот із перкою
Струбцина з напрямноюСтрубцина з напрямною
8

Make and place the bridge

Make the bridge 6 in long, 1 in wide and 3/8 in high, with an old hatpin or wire of the same size secured on top with pin staples as the saddle E. Drill six 3/16 in holes in it for the pins. Glue it on the top so the distance from the nut F to the saddle E is just 24 in.

Матеріали для цього кроку:

Смуга твердої деревиниСмуга твердої деревини1 штука
Капелюшна шпилькаКапелюшна шпилька1 штука
Дротяна скобаДротяна скоба1 штука
Столярний клейСтолярний клей1 штука

Необхідні інструменти ({count})

Коловорот із перкоюКоловорот із перкою
Ручна пилкаРучна пилка
РулеткаРулетка
9

String it

Fit the turning pegs B in the head and string the guitar, holding the strings in the bridge with the pins. He bought the pegs and strings from a music store.

Матеріали для цього кроку:

КілкиКілки1 штука
Гітарні струниГітарні струни1 штука
Штифти підставкиШтифти підставки1 штука

Необхідні інструменти ({count})

Коловорот із перкоюКоловорот із перкою
10

Troubleshooting

Guitar troubleshooting.

Flow

Loading...
11

History and honest limits

From **The Boy Mechanic**, edited by H. H. Windsor, Popular Mechanics, Chicago, 1913, p. 320, "A Guitar That Is Easy to Make", sent in by J. H. Stoddard of Carbondale, Pa.; sizes read on the 1913 scan (archive.org boymechanicthing01unse). He dimensions only the first five fret spaces, and they disagree with equal temperament; the fret positions used are computed by us. The sound hole, saddle and string tensions are not dimensioned. The tools and metric figures are ours.

Матеріали

12

Необхідні інструменти

8

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...