Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Workbench for the Amateur: Mortised Maple Frame, Two-Board Top, Side and End Vises (Boy Mechanic, 1913)
Woody

Створено

Woody

13. листопад 2026NO
6
0
0
0
0

Workbench for the Amateur: Mortised Maple Frame, Two-Board Top, Side and End Vises (Boy Mechanic, 1913)

A full-size woodworking bench from The Boy Mechanic (Popular Mechanics, 1913), "suitable for the amateur woodworker" and made "by anyone who has a few sharp tools and a little spare time": a mortise-and-tenon frame of birch or maple bolted with lag screws, a top of a 2 in and a 1 in board, a side vise and an end vise on square slides, and a back board. All sizes are the book's. It stands 36 in high, 80 in long and 24 in deep.
Середній
About 2 days

Інструкції

1

Cutting list

Завантаження блокнота Jupyter…
2

Read The Boy Mechanic

"If the stock is purchased from the mill ready planed and cut to length, much of the hard labor will be saved."
3

Make the lower frame

Cut tenons on the side and end rails and mortise the posts to take them. Fit them together and fasten them securely with 3/8 by 5 in lag screws through the posts into the rails, as the drawing shows.

Матеріали для цього кроку:

БрусБрус1 штука
Глухар (шуруп під ключ)Глухар (шуруп під ключ)1 штука

Необхідні інструменти ({count})

Дворучна поперечна пилкаДворучна поперечна пилка
Обушкова пилкаОбушкова пилка
Долото для гніздДолото для гнізд
Дерев'яний молоток (киянка)Дерев'яний молоток (киянка)
Столярний косинецьСтолярний косинець
Коловорот із перкоюКоловорот із перкою
Розвідний ключРозвідний ключ
ОлівецьОлівець
4

Fit the crosspieces and top

Screw the 1-1/2 by 3 by 24 in crosspieces to the tops of the posts, countersinking the heads (or bore the top boards to clear them). Fasten the front, 2 in top board to the crosspieces with lag screws from underneath; screw the 1 in top board down from the top.

Матеріали для цього кроку:

БрусБрус1 штука
Дошка твердої деревиниДошка твердої деревини1 штука
Дошка з твердої деревиниДошка з твердої деревини1 штука
Глухар (шуруп під ключ)Глухар (шуруп під ключ)1 штука
Шурупи по деревуШурупи по дереву1 штука

Необхідні інструменти ({count})

Коловорот із перкоюКоловорот із перкою
Набір зенківокНабір зенківок
Набір викрутокНабір викруток
Розвідний ключРозвідний ключ
5

Fit the end pieces and vise slides

Screw on the end pieces, countersinking the heads at the vise end. Cut 2 in square holes in the 1-1/2 by 4-1/2 by 10 in piece for the side vise slides and fit it in place, and cut square holes in one end piece for the end vise slides.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Шурупи по деревуШурупи по дереву1 штука

Необхідні інструменти ({count})

Коловорот із перкоюКоловорот із перкою
СтамескиСтамески
Дерев'яний молоток (киянка)Дерев'яний молоток (киянка)
Набір зенківокНабір зенківок
Набір викрутокНабір викруток
6

Fit up the two vises

Screw the 2 in square slides (guides) to the two clamp front pieces, countersinking the heads so they are clear of the hands. The clamp screws should be about 1-1/2 in diameter, bought at a hardware store. Fit a block under the crosspiece to hold the end vise's nut. With the slides in place, bore the holes for the clamp screws and fit them.

Матеріали для цього кроку:

БрусБрус1 штука
Дошка з твердої деревиниДошка з твердої деревини1 штука
Гвинт лещат із ковзним вороткомГвинт лещат із ковзним воротком2 штук
Шурупи по деревуШурупи по дереву1 штука

Необхідні інструменти ({count})

Коловорот із перкоюКоловорот із перкою
Набір зенківокНабір зенківок
Набір викрутокНабір викруток
7

Back board and finish

Screw the back board to the back as the top view shows. Give the bench "a couple of coats of oil" to finish and preserve the wood (boiled linseed oil, ours).

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Шурупи по деревуШурупи по дереву1 штука
Варена лляна оліяВарена лляна олія1 штука
Бавовняна тканинаБавовняна тканина1 штука

Необхідні інструменти ({count})

Набір викрутокНабір викруток
8

Troubleshooting

Workbench troubleshooting.

Flow

Loading...
9

History and honest limits

From **The Boy Mechanic, Volume 1: 700 Things for Boys to Do**, edited by H. H. Windsor, Popular Mechanics, Chicago, 1913 (Project Gutenberg #12655), "A Workbench for the Amateur". All sizes and the fastening are the book's; it names no oil, so boiled linseed oil is ours, as are the metric figures.

Матеріали

8

Необхідні інструменти

11

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...