Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Brazing Torch: a Pressure-Tank Gasoline or Kerosene Torch (Shop Notes, 1909)
Forge

Створено

Forge

4. листопад 2026NO
14
0
0
0
0

Brazing Torch: a Pressure-Tank Gasoline or Kerosene Torch (Shop Notes, 1909)

A shop brazing and tempering torch: a wall-hung pipe tank of gasoline or kerosene pumped up with a bicycle pump, feeding a 1/8 in pipe whose end is coiled round a short 1 in pipe; the flame heats the coil, the oil turns to gas, and it blasts out through a pinhole cap. Two burners on a tee give a bigger heat. Source: Popular Mechanics Shop Notes for 1909, pp. 861-862. Picture: the article's drawing.
Середній
Unknown

Інструкції

1

Make the tank

Cap both ends of a 2 in pipe 20 in long. Drill three holes in the top cap: one for the rubber tube from a bicycle pump, one for a steam gauge, and one with a screw plug for filling with fuel oil.

Матеріали для цього кроку:

Сталева труба (товстостінна, з різьбовими кінцями)Сталева труба (товстостінна, з різьбовими кінцями)1 2 in x 20 in
Різьбовий трубний фітингРізьбовий трубний фітинг3 two caps, plug
МанометрМанометр1 штука
Гумова трубкаГумова трубка1 штука

Необхідні інструменти ({count})

Ручний дрильРучний дриль
Набір мітчиків і плашокНабір мітчиків і плашок
Трубний ключТрубний ключ
Підлоговий велосипедний насосПідлоговий велосипедний насос
2

Coil the burner

Drill the bottom cap and connect a 1/8 in pipe D, any length, with a globe valve in it to set and shut off the oil. Fill the last 10 in of the pipe with lead, coil it round a 1 in pipe F 6 in long, and turn the end out to take two elbows and a short nipple; then melt the lead out. Drill a small hole in the centre of a 1/8 in cap and fit it on the end (E) so the hole lines up with the centre of pipe F.

Матеріали для цього кроку:

Сталева труба (товстостінна, з різьбовими кінцями)Сталева труба (товстостінна, з різьбовими кінцями)1 1/8 in, and 1 in x 6 in
Різьбовий трубний фітингРізьбовий трубний фітинг4 two elbows, nipple, 1/8 in cap
ВентильВентиль1 штука

Необхідні інструменти ({count})

СвинецьСвинець
Дірчаста шумівкаДірчаста шумівка
ГорноГорно
Ручний дрильРучний дриль
Трубний ключТрубний ключ
3

Start the burner

Hang a little cup holding three or four teaspoonfuls of oil just below the coil and light it to heat the coil; then pump up the tank and open the globe valve. For more heat connect two burners on a tee so their blasts meet.

Необхідні інструменти ({count})

ГасГас
Підлоговий велосипедний насосПідлоговий велосипедний насос

Матеріали

5

Необхідні інструменти

8

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...