Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Ring-Disk Spiral-Pin Churn: Cream Forced Out Between Corrugated Rings, Then Drawn to the Middle by Spiral Pins
Buttercup

Створено

Buttercup

11. листопад 2026IE
4
0
0
0
0

Ring-Disk Spiral-Pin Churn: Cream Forced Out Between Corrugated Rings, Then Drawn to the Middle by Spiral Pins

Daniel C. Brown of New York received US 26,880, dated 24 January 1860, for a churn. Cream poured into a hopper runs into the middle of a still disk at the bottom of a box, under a turning disk; their corrugated rings run between each other without touching, so the cream is flung outward and must climb over ring after ring. Above, the turning shaft carries pins set in two spirals that meet in the middle, drawing the butter there to be gathered. The patent gives no sizes; every size here is ours.
Середній
About 2 days, plus printing

Інструкції

1

Rings that never touch

Завантаження блокнота Jupyter…
2

Agitators passing between each other, two months before

Cornell's arms pass between those of a second shaft. Brown's rings run between the rings of a still disk.
3

Read US 26,880

"The milk or cream thus entering while the disk G is in rapid motion, it will be seen that (by the centrifugal force developed) the fluid will be forced outward, but, meeting the obstruction of the rings, will be checked—accumulate to some extent until forced to climb over and around them, successively advancing thus and being checked and being thereby subjected to the action of the corrugated surfaces upon each side of the rings"
4

Print the still disk F

A disk 236 mm across with three corrugated rings 8 mm thick and 12 tall at 40, 74 and 108 mm, a 21 mm bearing for G's journal, a 13 mm inlet beside it for the spout, and three feet. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
5

Print the turning disk G

A disk 236 mm across with two corrugated rings at 57 and 91 mm, a 20 mm journal below and a hub above with a cross hole for the shaft's pin. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
6

Print the gear wheel

Spur wheel, 48 teeth, module 3, 15 mm face, with a hub bored 20.6 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
7

Print the geared stud's pinion

Spur pinion, 16 teeth, module 3, 15 mm face, with a hub bored 20.6 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
8

Box A, hopper B and spout C

From 20 mm hardwood make a box 300 x 300 mm and 450 mm deep inside with a lid bored 21 mm in its middle. Bore one side 13 mm, 10 mm above the floor in its middle. Bend a 12 mm stainless tube to run from outside, through that hole along the floor and up into F's inlet, seal it through the side, and fit a stainless funnel on its outer end as the hopper. Fill the box with water overnight so it swells tight, then empty it.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини3 штук
Столярний клейСтолярний клей1 штука
Шурупи по деревуШурупи по дереву30 штук
Труба з нержавкої сталіТруба з нержавкої сталі1 штука
Лійка з нержавної сталіЛійка з нержавної сталі1 штука
Силіконовий герметикСиліконовий герметик1 штука

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
Ручна пилкаРучна пилка
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір перових сверделНабір перових свердел
Ножівка по металуНожівка по металу
Струбцина з напрямноюСтрубцина з напрямною
РулеткаРулетка
ВодаВода
9

Disks, shaft D and pins b

Stand F on its feet in the middle of the floor over the spout. Plane a hardwood shaft to a hexagon 40 mm across the flats and 393 mm long, with a 19 mm square socket 30 mm deep in its top, and pin its foot in G's hub. Bore twelve 16 mm holes through it from 35 to 332 mm above its foot, 27 mm apart, and glue in hardwood pins reaching 135 mm from the middle: the lower six turning 60 degrees each from the foot upward, the upper six the same from the top downward, so the two spirals meet at the middle. Set G's journal in F's bearing.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука
Столярний клейСтолярний клей1 штука
ШплінтШплінт1 штука
Філамент PETGФіламент PETG1 штука

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
Токарний верстат по деревуТокарний верстат по дереву
Циркулярний верстатЦиркулярний верстат
Долото для гніздДолото для гнізд
Дерев'яний молоток (киянка)Дерев'яний молоток (киянка)
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Наждачний папірНаждачний папір
10

Geared stud and crank E

Pass a 20 mm stainless stud through the lid, square at its foot to drop into the shaft's socket, with the pinion pinned on top. Fix a second stud in the lid 96 mm away carrying the gear wheel, meshing, with a crank and handle on it. Lift the lid to free the shaft and disks for cleaning.

Матеріали для цього кроку:

Пруток із нержавкої сталіПруток із нержавкої сталі2 штук
Дошка з твердої деревиниДошка з твердої деревини1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука
Плоска шайбаПлоска шайба4 штук
ШплінтШплінт2 штук

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
11

The build in 3D

FreeCAD model of this build, cut through the middle: the box, the spout running into the still disk, the turning disk with its rings between the still disk's, the hexagonal shaft with its two spirals of pins, and the geared stud, wheel and crank on the lid. The rotor was turned through 16 positions.
Файл дизайнуBLENDCC0 - Free
12

Churn

Turn the crank and pour heavy cream at about 15 °C, checked with the thermometer, into the hopper, about 15 litres in all, keeping the disk turning fast. Keep turning, timing it. When the butter comes the pins gather it in the middle: lift the lid, take out the shaft and the butter, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки15 l
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
13

Troubleshooting

Ring-disk churn troubleshooting.

Flow

Loading...
14

History and honest limits

**Daniel C. Brown** of New York, US 26,880, 24 January 1860, "Churn". He claimed the disks F and G with the rings on their inner sides. His disks were wood or metal; ours are printed. His hopper is a jointed bucket; ours is a funnel on a tube. The patent gives no sizes; every size here is ours.

Матеріали

14

Необхідні інструменти

19

Файли дизайну

5

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...