Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Spatter-Guard Spring Dasher Churn: A Funnel-and-Bowl Block on the Lid Keeps the Cream In, a Spring Lifts the Dasher
Buttercup

Створено

Buttercup

11. листопад 2026IE
4
0
0
0
0

Spatter-Guard Spring Dasher Churn: A Funnel-and-Bowl Block on the Lid Keeps the Cream In, a Spring Lifts the Dasher

John M. Buell of Zanesville, Ohio, received US 29,460, dated 7 August 1860, for an add-on to the common dasher churn. A block on the lid has a bowl underneath that catches the spatters and a funnel on top that takes back the cream wiped off the handle. A spiral spring from the block to a head block clamped on the handle lifts the dasher again after every push, so churning is only pushing down. The patent gives no sizes; every size here is ours.
Початківець
About 1 day

Інструкції

1

Choosing the spring B

Завантаження блокнота Jupyter…
2

A spring that lifts the dasher, a month before

Cooper lifts the dasher with rubber springs on a lever frame. Buell puts one coil spring straight round the handle.
3

Read US 29,460

"Press down g; C being attached will be carried down by it, thus compressing B. When down B will immediately expand and raise g to the same point again and so it will continue to operate making the labor of churning to consist merely in pushing down the dasher."
4

Churn, lid F and dasher

Use a 20-litre food-grade bucket as the common churn. Cut a 12 mm HDPE lid F 304 mm across with a 30 mm hole in the middle. Cut two hardwood boards 220 x 40 x 16 mm, cross them, and screw them to the foot of a 25 mm hardwood handle g 1000 mm long.

Матеріали для цього кроку:

Відро на 20 літрівВідро на 20 літрів1 штука
Лист ПЕВГЛист ПЕВГ1 штука
Дошка з твердої деревиниДошка з твердої деревини1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука
Столярний клейСтолярний клей1 штука
Шурупи по деревуШурупи по дереву4 штук

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
ЕлектролобзикЕлектролобзик
Набір перових сверделНабір перових свердел
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір викрутокНабір викруток
5

Device A: bowl d and funnel E

Glue up hardwood and turn a block A 90 mm across and 90 mm tall. Bore it 27 mm through the middle, so the handle is wiped as it rises. Turn the top into a funnel E, 60 mm across at the top narrowing to the bore 40 mm down, and hollow the underside into a half-round bowl d 70 mm across.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Столярний клейСтолярний клей1 штука

Необхідні інструменти ({count})

Токарний верстат по деревуТокарний верстат по дереву
Набір різьбярських стамесокНабір різьбярських стамесок
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
РулеткаРулетка
6

Spring B, head block C and thumb screw s

Get a compression spring about 73 mm outside, 280 mm long free and about 0.15 N per mm (16 turns of 3 mm wire). Turn a hardwood head block C 90 mm across and 30 thick, bored 26 mm. Bore its side 8.5 mm to the bore, let an M8 hex nut into the hole's mouth with glue, and run in an M8 threaded rod 50 mm long with a wing nut locked by a hex nut on its outer end: the thumb screw s. Fix one end of the spring to the rim of A's top and the other under C, each under a screw and washer, so A, B and C lift off as one.

Матеріали для цього кроку:

Набір пружин стискуНабір пружин стиску1 штука
Дошка з твердої деревиниДошка з твердої деревини1 штука
Шпилька різьбоваШпилька різьбова1 штука
Шестигранна гайкаШестигранна гайка2 штук
Гайка-баранецьГайка-баранець1 штука
Плоска шайбаПлоска шайба2 штук
Шурупи по деревуШурупи по дереву2 штук
Столярний клейСтолярний клей1 штука

Необхідні інструменти ({count})

Токарний верстат по деревуТокарний верстат по дереву
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Розвідний ключРозвідний ключ
Набір викрутокНабір викруток
7

The build in 3D

FreeCAD model of this build, the bucket and block A cut open: the dasher and handle, the lid, block A with its bowl underneath and funnel on top, the spring, and the head block with its thumb screw.
Файл дизайнуBLENDCC0 - Free
8

Set the stroke and churn

Pour about 10 litres of heavy cream at about 15 °C, checked with the thermometer, into the churn, stand the dasher in, and put on the lid. Slide A, B and C down the handle until A rests on the lid. Raise the handle to the top of its stroke, about 150 mm above where the dasher meets the bottom, and turn the thumb screw tight. Push the handle down and let the spring lift it, steadily, timing it. When the butter comes, loosen the thumb screw and lift A, B and C off the handle, take out the dasher and butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки10 l
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
9

Troubleshooting

Spring dasher churn troubleshooting.

Flow

Loading...
10

History and honest limits

**John M. Buell** of Zanesville, Muskingum County, Ohio, US 29,460, 7 August 1860, "Churn". He claimed "the device A constructed as described, in combination with the churn, spring B, handle g, and head block C". His churn was the common staved dasher churn with its own lid; ours is a bucket. The patent gives no sizes; every size here is ours.

Матеріали

14

Необхідні інструменти

16

Файли дизайну

1

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...