Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Rocking Bucket-Dasher Churn: A Crank and Rod Rock a Dasher of Bucketed Arms, a Fixed Bucket Breaks the Current
Buttercup

Створено

Buttercup

11. листопад 2026IE
8
0
0
0
0

Rocking Bucket-Dasher Churn: A Crank and Rod Rock a Dasher of Bucketed Arms, a Fixed Bucket Breaks the Current

Gillett Bunting of Liberty, Indiana, received US 26,226, dated 22 November 1859, for a churn-dasher. A dasher of crossed arms with buckets on their ends rocks on a level shaft whose bearings slide up or down to suit the amount of cream. A crank above, turned through a pair of cog wheels with a balance wheel, rocks it by a long rod, throwing the cream into opposing currents, and a fixed bucket on the bottom breaks the current along the floor. The patent gives no sizes; every size here is ours.
Середній
About 2 days, plus printing

Інструкції

1

How far the dasher rocks

Завантаження блокнота Jupyter…
2

Agitators swung on pivots, two weeks before

Cooper swings his agitators from a dash rod worked by hand. Bunting rocks a whole dasher from a crank.
3

Read US 26,226

"the rapid oscillating motion thus imparted to the dasher, through the medium of buckets (e' g', K) forces the cream into violent opposing currents, at the same time, the concussive action of the buckets (e', g') and arms (e, g) and bar (E) upon the cream is fully developed, thereby producing, a rapid and violent agitation of the cream"
4

Print the driving wheel G

Spur wheel, 48 teeth, module 3, 15 mm face, with a hub bored 20.6 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
5

Print the wheel h

Spur pinion, 16 teeth, module 3, 15 mm face, with a hub bored 12.6 mm and a cross hole for a pin. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
6

Shell A, bed A', guides L and bucket K

Use a wooden tub 360 mm across inside at the floor, 320 mm at the top and 420 mm deep. Stand it on a bed board 520 x 560 mm between two guide strips. Glue and screw a hardwood block K, 60 x 300 x 60 mm, across the middle of the floor, with a 24 x 24 mm socket 50 mm deep near each end for the slides. Fill the tub with water overnight so it swells tight, then empty it.

Матеріали для цього кроку:

Дерев'яна діжкаДерев'яна діжка1 штука
Дошка з твердої деревиниДошка з твердої деревини2 штук
Столярний клейСтолярний клей1 штука
Шурупи по деревуШурупи по дереву12 штук

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
Ручна пилкаРучна пилка
Долото для гніздДолото для гнізд
Дерев'яний молоток (киянка)Дерев'яний молоток (киянка)
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Струбцина з напрямноюСтрубцина з напрямною
РулеткаРулетка
ВодаВода
7

Slides f and the dasher

Cut two slides 20 x 24 mm, 255 mm long, bore each 21 mm 225 mm from its foot for the shaft's journal, and a row of 6 mm holes near the foot for a set screw through the block K. Make the shaft F a 20 mm hardwood dowel 280 mm long. Mortise through it two arms e 20 x 30 mm, 210 mm long, 150 mm apart, two arms g 20 x 30 mm, 260 mm long, at right angles to them, 80 mm apart, and the bar E 20 x 30 mm, 235 mm long, between the arms e, its long end reaching 100 mm past the shaft and bored 12.6 mm. Screw three U-channel buckets 170 x 40 x 20 mm of hardwood across the ends: one on the arms e and E's short end, one on each end of the arms g. Stand the slides in K with the shaft's ends in them, 240 mm up.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини2 штук
Шканти з твердої деревиниШканти з твердої деревини1 штука
Столярний клейСтолярний клей1 штука
Шурупи по деревуШурупи по дереву24 штук
Набір шестигранних болтівНабір шестигранних болтів2 штук

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
Ручний фрезерРучний фрезер
Долото для гніздДолото для гнізд
Дерев'яний молоток (киянка)Дерев'яний молоток (киянка)
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Наждачний папірНаждачний папір
РулеткаРулетка
8

Frame B, crank shaft C, wheels and rod D

Bolt two posts of 40 x 30 mm hardwood to the bed beside the tub, 400 mm apart, 850 mm tall, and bore them 12.6 mm 690 mm above the tub's floor. Bend a 12 mm stainless shaft C into a crank of 50 mm throw in its middle, heating the bends red with the torch, and run it through the posts over the bar E's end. Pin the wheel h on one end and a hardwood balance wheel k, 260 mm across and 30 mm thick, on the other. Fix a 20 mm stud above h for the wheel G, meshing, with a crank handle H. Join the crank to E's end with a hardwood rod D, 450 mm between its pins.

Матеріали для цього кроку:

Хвойний брус 70x70 ммХвойний брус 70x70 мм1 штука
Дошка з твердої деревиниДошка з твердої деревини2 штук
Пруток із нержавкої сталіПруток із нержавкої сталі2 штук
Shaft CollarShaft Collar2 штук
ШплінтШплінт4 штук
Плоска шайбаПлоска шайба6 штук
Набір шестигранних болтівНабір шестигранних болтів4 штук
Самоконтрувальна гайка з нейлоновим кільцемСамоконтрувальна гайка з нейлоновим кільцем4 штук
Філамент PETGФіламент PETG1 штука

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
Пропановий пальникПропановий пальник
Слюсарні лещатаСлюсарні лещата
МолотокМолоток
Термостійкі рукавиціТермостійкі рукавиці
ЕлектролобзикЕлектролобзик
КомпасКомпас
Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Розвідний ключРозвідний ключ
9

The build in 3D

FreeCAD model of this build, the tub cut through the middle: the bed and guides, the fixed bucket K with the two slides, the dasher with its arms, bar E and three buckets, the rod D up to the cranked shaft C, the wheels G and h, the crank H and the balance wheel. The crank was turned through 24 positions.
Файл дизайнуBLENDCC0 - Free
10

Churn

Pour in heavy cream at about 15 °C, checked with the thermometer; for less cream, lower the slides in K so the dasher still works in it. Turn the crank H steadily, timing it. When the butter comes, lift the rod off the crank and the dasher out on its slides, take out the butter, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки15 l
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
11

Troubleshooting

Rocking dasher troubleshooting.

Flow

Loading...
12

History and honest limits

**Gillett Bunting** of Liberty, Union County, Indiana, assignor to himself and W. M. Jarrell, US 26,226, 22 November 1859, "Churn-Dasher". He disclaimed hinged churn-dashers and oscillating movement as such, and claimed the vibrating movement of the dasher by the arms with the crank, driving wheel and connecting rod, with the current breaker K. The patent gives no sizes; every size here is ours. His frame B stands on the shell's top; ours is two posts on the bed beside it.

Матеріали

16

Необхідні інструменти

25

Файли дизайну

3

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...