Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Button-Set Hinged-Slat Dasher Churn: Slats Deflect the Cream, a Button on the Rod Holds Them Open or Lets Them Shut
Buttercup

Створено

Buttercup

11. листопад 2026IE
7
0
0
0
0

Button-Set Hinged-Slat Dasher Churn: Slats Deflect the Cream, a Button on the Rod Holds Them Open or Lets Them Shut

S. N. Campbell of Elgin, Illinois, received US 25,804, dated 18 October 1859, for a churn. A lever pivoted on a post works a dasher that fits the box closely. Its hinged slats hang open as deflectors: drawn up, the dasher throws the cream down and to the sides; pushed down, it forces the cream up towards a cross piece in the middle. A button with two inclined surfaces on the rod's foot holds the slats open, or, turned half round, lets them shut on the down stroke, to suit the cream. The patent gives no sizes and does not say where the slats are hinged or how the button bears on them: those and every size here are ours.
Середній
About 2 days, plus printing

Інструкції

1

The button: holding the slats open, or letting them shut

Завантаження блокнота Jupyter…
2

An up-and-down dasher fitting a box closely, three weeks before

Austin's middle dasher is a plain plate. Campbell's has hinged slats that deflect the cream, held open or let shut by a button on the rod.
3

Read US 25,804

"This dasher is constructed with movable slats H, H, which, when open, rest upon stop pins a, and serve the office of deflectors, and as the dasher is drawn up the cream is thrown below the slats and to the sides of the churn and as the dasher is pressed down the cream will be forced up and toward the center of the churn, and against a cross piece J, secured to the center of the dasher."
4

Print the button K

A disc 72 mm across and 6 mm thick with two inclined surfaces 60 mm long, one each side, both rising 7.5 mm towards the same end. PETG, 0.2 mm layers, 100 % infill.
Файл дизайнуSTLCC0 - Free
5

Box A, stand B, post D, lid E and lever C

From 20 mm hardwood make a box 400 x 300 mm and 380 mm deep inside, on four legs 50 mm square and 300 mm long. Screw a post 50 x 40 mm, 860 mm long, up the middle of the back. Cut a lid with a 32 mm hole in its middle. Bolt a lever 30 x 30 mm, 640 mm long, to the post's top so it reaches over the lid's middle to the front. Fill the box with water overnight so it swells tight, then empty it.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини3 штук
Хвойний брус 70x70 ммХвойний брус 70x70 мм1 штука
Столярний клейСтолярний клей1 штука
Шурупи по деревуШурупи по дереву30 штук
Набір шестигранних болтівНабір шестигранних болтів2 штук
Самоконтрувальна гайка з нейлоновим кільцемСамоконтрувальна гайка з нейлоновим кільцем2 штук
Плоска шайбаПлоска шайба4 штук

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
Ручна пилкаРучна пилка
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір перових сверделНабір перових свердел
Струбцина з напрямноюСтрубцина з напрямною
Столярний косинецьСтолярний косинець
РулеткаРулетка
ВодаВода
Розвідний ключРозвідний ключ
6

Dasher G and its slats

Make two end bars 296 x 40 x 20 mm and join them with the cross piece J, 396 x 40 x 30 mm, bored 31 mm in its middle. Cut two inner slats H 380 x 63 x 12 mm, each with a tab 20 x 9 mm on its inner edge 10 to 30 mm from the middle, and two outer slats H' 380 x 52 x 12 mm. Bore each along its length for a 6 mm stainless hinge pin, H 3 mm in from its inner edge and H' 4 mm in, and hang them between the end bars on pins 392 mm long, H 32 mm and H' 98 mm each side of the middle. Fix 6 mm stop pins, 20 mm long, into the end bars under the slats: 80 mm out and 27 mm below the hinges for H, 130 mm out and 21.5 mm below for H'. Glue posts 20 x 10 x 19 mm on the slats, 120 mm each side of the middle, 40 mm out from each hinge, and join each pair with a piece L 76 x 20 x 6 mm on pins.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини2 штук
Пруток із нержавкої сталіПруток із нержавкої сталі2 штук
Столярний клейСтолярний клей1 штука
ШплінтШплінт12 штук
Плоска шайбаПлоска шайба12 штук

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Наждачний папірНаждачний папір
РулеткаРулетка
Струбцина з напрямноюСтрубцина з напрямною
7

Rod F and button K

Turn a hardwood rod F 30 mm across and 440 mm long, with a cross handle at its top to turn it. Pass it down through J and glue the button on its foot, below J, so that in one position its inclined surfaces lie under the slats' tabs and hold the slats open on their pins. Join its top to the lever with a pin in a slot. Set the dasher in the box and the lid on.

Матеріали для цього кроку:

Шканти з твердої деревиниШканти з твердої деревини1 штука
Столярний клейСтолярний клей1 штука
Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
ШплінтШплінт2 штук
Філамент PETGФіламент PETG1 штука

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Ножівка по металуНожівка по металу
8

The build in 3D

FreeCAD model of this build, one side and one end left off: the box on its stand, the post and lever, the rod, and the dasher with the cross piece J, the hinged slats H and H' on their stop pins, the pieces L and the button K under the tabs. Checked at three heights, with the slats held open and with them shut.
Файл дизайнуBLENDCC0 - Free
9

Churn

Pour about 20 litres of heavy cream at about 15 °C into the box, checked with the thermometer, and put the lid on. Work the lever up and down, timing it. For thin cream keep the button holding the slats open; if the cream thickens, turn the rod half round so the slats shut on each down stroke. When the butter comes, lift the dasher out, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки20 l
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
10

Troubleshooting

Hinged-slat dasher troubleshooting.

Flow

Loading...
11

History and honest limits

**S. N. Campbell** of Elgin, Kane County, Illinois, US 25,804, 18 October 1859, "Churn". He claimed "the arrangement and combination of the button K, dasher rod F, movable slats H, H', pieces L, and bar J". The patent gives no sizes and does not say where the slats are hinged, how the button's surfaces bear on them, or how the pieces L join H' to H: the hinge lines, the tabs, the button's surfaces, the links and every size here are our reading.

Матеріали

14

Необхідні інструменти

18

Файли дизайну

2

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...