Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Carbon Steel Strip: Saw Plate Sheared and Annealed Soft
Forge

Створено

Forge

26. жовтень 2026NO
17
0
0
0
0

Carbon Steel Strip: Saw Plate Sheared and Annealed Soft

Thin carbon steel strip, soft enough to punch, file and score: the stock for utility-knife blades, hacksaw blades and hole saws, which are hardened only after they are shaped. Start from crucible steel rolled to gauge, cut it into strips with plate shears, then anneal it the way Harcourt's Elementary Forge Practice (1920) gives for tool steel: cherry red, about 1400 °F, and buried in perfectly dry ashes until cold. Cutting strips instead of saw outlines and the file test are ours. The picture is our drawing.
Початківець
1 day (cooling overnight)

Інструкції

1

Roll the plate

Roll crucible steel to the gauge the blades need, as in this blueprint. Stop before the saw outlines are sheared.
2

Mark the strips

Scribe lines along the plate, one strip width apart. The width is whatever the blades need (ours).

Матеріали для цього кроку:

Листова сталь для пилкових полотенЛистова сталь для пилкових полотен1 штука

Необхідні інструменти ({count})

РисувалкаРисувалка
Повірочна лінійкаПовірочна лінійка
3

Shear into strips

Cut along the lines with plate shears, as Grimshaw's saw plates are cut to outline after rolling.

Необхідні інструменти ({count})

Листові ножиціЛистові ножиці
4

Fill a bucket with dry ash

Fill an iron bucket with ashes. They must be perfectly dry, so they conduct heat poorly and the steel cools slowly. Dry slaked lime also works.

Необхідні інструменти ({count})

Попіл твердої деревиниПопіл твердої деревини
Металеве відроМеталеве відро
5

Heat to cherry red

Heat the strips evenly in the forge to a cherry red, about 1400 °F (760 °C). No hotter: overheated steel goes coarse in the grain and weak.

Необхідні інструменти ({count})

Кувальне горноКувальне горно
Ковальські кліщіКовальські кліщі
Зварювальні рукавиціЗварювальні рукавиці
6

Bury and leave until cold

Bury the strips in the ash at once and leave them until they are entirely cold, overnight. The slower they cool, the softer they are.

Необхідні інструменти ({count})

Ковальські кліщіКовальські кліщі
Металеве відроМеталеве відро
Зварювальні рукавиціЗварювальні рукавиці
7

Check it is soft

Brush off the ash and stroke a corner with a file: it should bite easily. If it skates, anneal again (our test).

Необхідні інструменти ({count})

Напилок по металуНапилок по металу

Матеріали

1

Необхідні інструменти

9

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...