Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Rack-and-Pawl Plunge Router: The Motor Rides One Post on a Spring and Steps Down a Tooth at a Time (Carter, 1925)
Forge

Створено

Forge

13. листопад 2026NO
12
0
0
0
0

Rack-and-Pawl Plunge Router: The Motor Rides One Post on a Spring and Steps Down a Tooth at a Time (Carter, 1925)

Ray L. Carter of Syracuse, New York, improved his 1924 router with US 1,565,790, dated 15 December 1925. The motor's holder now slides up and down a single strong post on a large round base, and a spring inside the post holds it up off the work. Each press of a lever moves the holder down one tooth of a rack, so a deep cavity is cut in stages. A locking pawl holds each step. Gauge nuts on a plunger stem set the final depth, and pressing the pawl's foot lets the spring lift the cutter clear. We reuse our 1924 router's printed motor casing in a printed holder on a square steel post. The sizes are ours.
Просунутий
About 3 days

Інструкції

1

Cutting deep in stages

Завантаження блокнота Jupyter…
2

Read US 1,565,790

"By this arrangement cavities of considerable depth may be routed by successive stages wherein each stage represents the normal depth the tool is designed to cut."
3

The motor and its casing come from the 1924 router

Print the casing and fit the motor, collet and switch exactly as in Carter's 1924 router; here the casing screws into a holder on a post instead of into a base.
4

Print the holder

The holder 7: a split ring threaded for the 1924 casing, clamp lugs for a thumb screw, and beside it the guide 7c with a square opening for a 1 in tube, a recess for the gib plate, two set-screw holes and the rack 17 of 3 mm teeth on its outer face. Print it rack upright. PETG, 0.2 mm layers, 40 % infill, 5 walls; no supports.
Файл дизайнуSTLCC0 - Free
5

Print the base

The base 9: a round plate 170 mm across with a 50 mm opening, and the boss 9' with a square socket for the post and a hole for its cross bolt. Print it plate down. PETG, 0.2 mm layers, 40 % infill, 5 walls; no supports.
Файл дизайнуSTLCC0 - Free
6

The hollow post 8

Cut 1 inch square steel tube 200 mm long. Saw and file a slot 8b 6 mm wide and 100 mm long down the middle of one wall, starting 40 mm from the top. Push the post into the base's socket and bolt it through with an M6 bolt and lock nut. Drop a compression spring 10 into the post, then a plunger 13: a block of flat bar that slides in the tube, tapped M6 on its back for the screw that runs in the slot, with an M6 rod 13' standing up from it. Screw a flat-bar cap 12 across the post's top with a hole for the rod, and run two gauge nuts 14, 14' onto the rod above it.

Матеріали для цього кроку:

Mild Steel Square Tube 1" x 1"Mild Steel Square Tube 1" x 1"1 штука
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Набір пружин стискуНабір пружин стиску1 штука
Шпилька різьбоваШпилька різьбова1 штука
Шестигранна гайкаШестигранна гайка2 штук
Набір шестигранних болтівНабір шестигранних болтів3 штук
Самоконтрувальна гайка з нейлоновим кільцемСамоконтрувальна гайка з нейлоновим кільцем1 штука

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Набір напилківНабір напилків
Слюсарні лещатаСлюсарні лещата
Свердлильний верстатСвердлильний верстат
Набір сверделНабір свердел
Набір мітчиків і плашокНабір мітчиків і плашок
Коловорот для мітчиківКоловорот для мітчиків
Розвідний ключРозвідний ключ
Захисні окуляриЗахисні окуляри
7

Holder on the post

Print the holder and base. Lay a strip of flat bar in the guide's recess 15 as the gib plate 15' and run two M5 set screws 16 against it, one with a wing nut on its head to lock the holder by hand. Slide the guide down over the post and fix it to the plunger with an M6 screw through the slot. Set the screws so the holder slides freely without rattling. Screw the 1924 motor casing into the holder and lock it with an M5 screw and wing nut through the lugs.

Матеріали для цього кроку:

Філамент PETGФіламент PETG1 штука
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Установчий гвинт із чашоподібним кінцемУстановчий гвинт із чашоподібним кінцем2 штук
Гайка-баранецьГайка-баранець2 штук
Гвинт із циліндричною головкою та внутрішнім шестигранникомГвинт із циліндричною головкою та внутрішнім шестигранником2 штук

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
Знімач задирокЗнімач задирок
Набір шестигранних ключівНабір шестигранних ключів
Цифровий штангенциркуль 6 дюймівЦифровий штангенциркуль 6 дюймів
8

Pawls and lever

File a pawl 18 from flat bar with a hook 18' at its top to catch the rack's teeth, and a locking pawl 20 with a tooth 20' at its top and its lower end bent out as a foot 20d. Pivot the locking pawl on the base's boss with an M5 screw, held against the rack by a spring-steel leaf 20b. Pivot one end of a lever 19 on the boss and the pawl's lower end to the lever partway along, with a second leaf 20c holding the pawl to the rack. Each press of the lever's handle pulls the holder down one tooth, and the locking pawl drops in under it.

Матеріали для цього кроку:

Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі2 штук
Смуга пружинної сталіСмуга пружинної сталі1 штука
Гвинт із циліндричною головкою та внутрішнім шестигранникомГвинт із циліндричною головкою та внутрішнім шестигранником3 штук
Самоконтрувальна гайка з нейлоновим кільцемСамоконтрувальна гайка з нейлоновим кільцем3 штук

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Набір напилківНабір напилків
Слюсарні лещатаСлюсарні лещата
Свердлильний верстатСвердлильний верстат
Набір сверделНабір свердел
Розвідний ключРозвідний ключ
9

Rout a deep recess

Fit a straight bit. Set the gauge nuts so the plunger's rod stops on the cap at the depth wanted. Clamp a board, rest the base on it with the cutter clear, switch on, press the lever once and move the router across the area; press again and repeat, until the nuts stop it. Press the locking pawl's foot and the spring lifts the cutter out.

Необхідні інструменти ({count})

Набір фрезНабір фрез
Дошка з твердої деревиниДошка з твердої деревини
Струбцина з напрямноюСтрубцина з напрямною
Захисні окуляриЗахисні окуляри
10

Troubleshooting

Plunge router troubleshooting.

Flow

Loading...
11

History and honest limits

**Ray L. Carter** of Syracuse, New York, US 1,565,790, dated 15 December 1925, filed 21 March 1925, improving his US 1,514,894. He describes a holder "formed at one side with a guide portion having an angular vertical opening, for slidably mounting the holder upon a pedestal or post of substantially the same angularity", a coil spring housed in the pedestal, a ratchet rack and pawl to move the motor step by step, a locking pawl, gauge nuts, and a plate with set screws to take up wear. His post is triangular and cast; ours is 1 inch square steel tube. His holder and base are metal; ours are printed PETG. His motor ran on mains; ours is the small DC motor of our 1924 router. The sizes are ours.

Матеріали

12

Необхідні інструменти

16

Файли дизайну

2

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...