Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Clamping Caul: Plain Pine Board Shaped to the Work (Adamson, 1889)
Woody

Створено

Woody

9. листопад 2026NO
10
0
0
0
0

Clamping Caul: Plain Pine Board Shaped to the Work (Adamson, 1889)

A caul is a board laid over glued work so the clamps press evenly over the whole surface instead of only under their jaws. D. Adamson (1889) uses a piece of good sound pine about 1 in. thick, shaped exactly to fit the surface: flat for a flat panel, convex for a concave one. For veneering he warms it first. Wood can warp or twist, and burns if overheated; a zinc-faced caul (separate blueprint) lasts longer. Source: D. Adamson, "Practical Veneering", Work, 5 October 1889, pp. 453-455.
Початківець
Unknown

Інструкції

1

Read Adamson

"The caul itself is either wood or metal, either of which must be shaped exactly to fit the surface to be veneered. Thus for a flat panel it must be flat, while for a concave surface it must be convex, and so on. ... For the material nothing is more suitable than good sound pine."
2

Cut the board

Cut a piece of good sound pine about 1 in. thick, large enough to cover the whole surface to be pressed. Thicker is no better, only waste. The length and width are set by the work (not given).

Матеріали для цього кроку:

Соснова дошкаСоснова дошка1 about 1 in. thick

Необхідні інструменти ({count})

Столярна пилкаСтолярна пилка
Невідомі розміриНевідомі розміри
3

Shape it to the work

Plane the face that meets the work to fit it exactly: flat for a flat panel, convex for a concave surface. A caul that is hollow in the middle presses only at the edges. How it is trued is not given (ours: plane, checked with a straightedge).

Необхідні інструменти ({count})

Ручний рубанокРучний рубанок
Повірочна лінійкаПовірочна лінійка
4

Use it

Warm the caul (not so hot that it cannot be comfortably handled), lay it over the veneer with a sheet of slightly greased paper between, and screw down the hand-screws evenly until the glue oozes out at the edges. Leave it until the caul is cold, an hour or two.

Необхідні інструменти ({count})

СтрубциниСтрубцини

Матеріали

1

Необхідні інструменти

5

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...