Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Contrary Hinged-Dasher Air-Pump Churn: Two Crossing Dashers Fold to Gather, a Pump Blows Air Through the Cream
Buttercup

Створено

Buttercup

11. листопад 2026IE
4
0
0
0
0

Contrary Hinged-Dasher Air-Pump Churn: Two Crossing Dashers Fold to Gather, a Pump Blows Air Through the Cream

Philip L. Clow of Cohoes, New York, received US 26,092, dated 15 November 1859, for a churn. One crank shaft and two pairs of bevel wheels turn two upright plate dashers in opposite directions at the same speed, so close that their paths cross. Their outer parts are hinged: turned one way they stand open to churn, turned the other they fold back to gather the butter. A pump on the same shaft blows air in at the bottom, and hot or cold water under the vessel's bottom keeps the cream at the right warmth. The patent gives no sizes; every size here is ours.
Просунутий
About 2 days, plus printing

Інструкції

1

Two dashers whose paths cross, and the air the pump gives

Завантаження блокнота Jupyter…
2

A turning dasher with a hinged leaf for gathering, two months before

Hassler's leaf opens when the dasher is reversed. Clow hinges the outer halves of two counter-turning dashers so they fold back when reversed.
3

Read US 26,092

"I thus hinge the outer parts of the dashers to their central parts in order that after the butter has been produced from the milk or cream by turning the dashers in the directions pointed by the arrows x, x', the person who is churning may then, by simply turning the crank-shaft, I, and dashers, B, B', in the opposite direction, instantly lessen the extent of the space passed over or occupied by the dashers and thus increase the capacity of the churn or give room in the vessel, G, for the gathering of the butter into a mass"
4

Print the feet

A foot 30 mm across and 56 mm tall with a 10 mm recess in its top. Print three. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
5

Print the eccentric t

A disc 90 mm across and 12 mm thick bored 12.6 mm 30 mm off its centre, for a 30 mm throw. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
6

Vessel G on its reservoir F

Fit a brass spigot low in the side of a large pot at least 400 mm across, as the cock s. Stand the three printed feet in it and the stockpot on them, so water can lie under the stockpot's bottom and up its sides. Drill the stockpot's handle for the clamp hook m.

Матеріали для цього кроку:

Велика каструляВелика каструля1 штука
Велика каструляВелика каструля1 штука
Латунний кранЛатунний кран1 штука
Філамент PETGФіламент PETG1 штука

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
Акумуляторний дрильАкумуляторний дриль
Набір перових сверделНабір перових свердел
Розвідний ключРозвідний ключ
7

Cover n, posts, shafts and bevel wheels

Cut a hardwood cover 350 mm across, bored 13 mm at 55 mm either side of its middle for the dasher axes k, k', 10 mm for the thermometer and 12 mm for the air tube. Screw two posts 40 x 20 mm, 110 mm tall, on it 300 mm apart and bore them 12.8 mm 80 mm above the cover for the crank shaft I, 12 mm stainless, 442 mm long, with a crank and handle on one end. Fit the two bevel sets so the wheels on k and k' are driven from opposite sides by the pinions on I, back to back between them: the dashers then turn opposite ways at the same speed. Hold the axes in the cover with shaft collars.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Столярний клейСтолярний клей1 штука
Шурупи по деревуШурупи по дереву8 штук
Пруток із нержавкої сталіПруток із нержавкої сталі2 штук
Комплект конічних зубчастих коліс (сталь, 1:1)Комплект конічних зубчастих коліс (сталь, 1:1)2 штук
Shaft CollarShaft Collar4 штук
Гачок і петляГачок і петля1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука

Необхідні інструменти ({count})

ЕлектролобзикЕлектролобзик
КомпасКомпас
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Набір викрутокНабір викруток
Розвідний ключРозвідний ключ
РулеткаРулетка
8

Dashers B, B' with hinged leaves

From 2 mm stainless sheet cut two centre parts 50 x 220 mm and four leaves 65 x 220 mm. Fix a centre part to each axis k, k', 50 mm above the vessel's floor, and hang a leaf on each of its long edges with two small butt hinges, set so the leaves stop in line with the centre part one way and fold back the other. Set the two dashers a quarter turn apart.

Матеріали для цього кроку:

Лист нержавкої сталіЛист нержавкої сталі1 штука
Меблева карткова завісаМеблева карткова завіса8 штук
Машинні гвинтиМашинні гвинти24 штук
Самоконтрувальна гайка з нейлоновим кільцемСамоконтрувальна гайка з нейлоновим кільцем24 штук

Необхідні інструменти ({count})

Ножиці по металуНожиці по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір викрутокНабір викруток
Розвідний ключРозвідний ключ
9

Force-pump E and pipe u

Fix the eccentric on the crank shaft outside one post, and a 100 ml syringe upright beside it, its plunger joined to a strap round the eccentric. On its nozzle fit two check valves on a tee, one letting air in, the other out. Run silicone tube from the outlet to a stainless tube that passes down through the cover and along the vessel's side to 8 mm above its floor, its end turned inwards.

Матеріали для цього кроку:

Шприц - LuerШприц - Luer1 штука
Зворотний клапанЗворотний клапан2 штук
Силіконова трубкаСиліконова трубка1 штука
Труба з нержавкої сталіТруба з нержавкої сталі1 штука
Дошка з твердої деревиниДошка з твердої деревини1 штука
Шурупи по деревуШурупи по дереву4 штук

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір викрутокНабір викруток
10

The build in 3D

FreeCAD model of this build, the vessel, reservoir and cover cut through: the stockpot on its feet in the water pot, the two dashers on their axes a quarter turn apart, the bevel wheels and crank shaft on their posts, the eccentric and syringe pump, the air tube and the thermometer. The dashers were turned through a full turn with their leaves open and folded.
Файл дизайнуBLENDCC0 - Free
11

Churn, then gather

Fill the reservoir with warm or cold water until the cream will sit at about 15 °C. Pour about 12 litres of heavy cream into the stockpot, set the cover with the dashers in, hook it down, and put the thermometer through it. Turn the crank so the leaves stand open, timing it, while the pump bubbles air in at the bottom. When the butter comes, turn the crank the other way: the leaves fold back and the dashers gather the butter. Lift the cover and dashers out, gather the butter, empty the reservoir by the spigot, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки12 l
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
ЕлектрочайникЕлектрочайник
12

Troubleshooting

Contrary-dasher churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Philip L. Clow** of Cohoes, Albany County, New York, US 26,092, 15 November 1859, "Churn". He claimed the outer parts of the two contrarily revolving dashers hung to the central parts by hinges d, and the arrangement of the air-pump E and water-reservoir F with the revolving dashers and cream vessel. The patent gives no sizes; every size here is ours. His force-pump is not described inside: ours is a syringe with two check valves on an eccentric. His reservoir is a closed chamber under the vessel with a funnel, air-vent and cock; ours is an open pot of water with a spigot. His rubber packing between the pinions is left out.

Матеріали

23

Необхідні інструменти

17

Файли дизайну

3

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...