Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО

Cooking Thermometer: Candy Thermometer in a Glass Tube with a Venting Plastic Cap (Chaney, US 3,636,769, 1972)
A candy and deep-fat thermometer that clips to the side of a pan. A glass thermometer on a printed scale card sits inside a protective glass tube, so it never touches the candy. The top of the tube is closed by a polyethylene cap that seals in normal use but softens when the whole thermometer is heated far too hot, as in an oven, so the air inside escapes instead of bursting the tube.
Result: a pan-side cooking thermometer that cannot explode if overheated.
Source: J. L. Chaney, US 3,636,769 (1972). Unknown: the scale range, sizes and several materials. Picture: the patent drawing.
Середній
Unknown
Інструкції
1
1
Mount the thermometer on its scale
Mount the thermometer on its scale
Fasten a glass thermometer tube to a graduated scale card with small fasteners, the bulb at the bottom. The patent's card is marked with cooking points such as soft ball, hard ball, soft crack, hard crack, fish, fowl, potatoes and doughnuts. Fix a disk on top of the card to keep it centred in the outer tube. Not given: the range, the card and fastener materials.
Матеріали для цього кроку:
Лабораторний термометр1 thermometer tube
Невідомий матеріал1 scale card, disk
Невідомий метал1 fastenersНеобхідні інструменти ({count})
Невідомі розміри2
2
Enclose it in the protective tube
Enclose it in the protective tube
Slide the card and thermometer into a glass protective tube, open at the top, so the bulb reaches the lower end and touches a metal cap there to pass on the heat. Not given: the tube size, the metal of the end cap, how the cap is joined to the tube.
Матеріали для цього кроку:
Скляна трубка1 protective tube
Невідомий метал1 end capНеобхідні інструменти ({count})
Невідомі розміри3
3
Fit the venting cap
Fit the venting cap
Close the open top with a cup-shaped cap of a thermoplastic such as polyethylene, a friction fit that seals out dirt. Polyethylene softens at about 180 °F and melts near 250 °F: if the thermometer is heated in an oven to 400-550 °F, the air inside would reach 12-14 psi, but the cap distorts first and lets it out. Do not use rubber or a thermosetting plastic, which does not vent. Ours: LDPE.
Матеріали для цього кроку:
Гранули LDPE1 capНеобхідні інструменти ({count})
Невідомі розміри4
4
Fit the pan clip and use it
Fit the pan clip and use it
Slide a spring clip onto the outside of the tube; its spring arm holds the thermometer upright over the edge of the pan. Clip it on with the bulb end in the candy or fat and read the scale; it also serves for deep frying. Ours: spring steel wire.
Матеріали для цього кроку:
Пружинний сталевий дріт1 clipНеобхідні інструменти ({count})
КруглогубціМатеріали
6- 1 thermometer tubeЗаповнювач
- 1 scale card, diskЗаповнювач
- 1 end capЗаповнювач
- 1 protective tubeЗаповнювач
- 1 capЗаповнювач
- 1 clipЗаповнювач
Необхідні інструменти
2- Заповнювач
- Заповнювач
Матеріали з пов'язаних креслень

Небезпечно
10% атрибуція
Liquid-in-Glass Thermometer: Bulb, Fill, Seal and Scale
від Penny
Виробництво скла
42
0
0
0
1
0

Небезпечно
10% атрибуція
LDPE Pellets: Ethylene Polymerised at 1500 Atmospheres with a Trace of Oxygen
від Charlie
Індустріальний
14
0
0
0
2
0

10% атрибуція
Spring Steel Strip and Wire, Hardened and Tempered
від Forge
Металообробка
48
0
0
0
5
0
За цим кресленням виготовляють
CC0 Суспільне надбання
Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.
Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.
