Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Built-Up Shaft Collar: Two Washers Welded to Four Nuts, a Set Screw in One Nut, No Machining (Dalrymple, 1939)
Forge

Створено

Forge

13. листопад 2026NO
5
0
0
0
0

Built-Up Shaft Collar: Two Washers Welded to Four Nuts, a Set Screw in One Nut, No Machining (Dalrymple, 1939)

Ferdinand H. Dalrymple of Bedford, Ohio, received US 2,163,315, dated 20 June 1939, for a shaft collar "comprised of few parts which are readily obtainable as standard market articles". Two washers are held apart by nuts welded between them. The nuts' inner faces rest on the shaft, and a set screw in one nut's thread holds it. It needs no machining. He says it is stronger, lighter and cheaper than a cast collar, and breaks less readily under a hammer. It also touches the shaft only along lines, so it rusts to it less, and oil can be put in between the nuts. The patent gives no sizes for this form; every size here is ours.
Початківець
About 1 hour

Інструкції

1

Will it fit together?

Завантаження блокнота Jupyter…
2

Read US 2,163,315

"Preferably, I use as plates standard washers of suitable dimension, and I use as blocks standard nuts." "Inasmuch as the space between the plates is not sufficient for the convenient manipulation of an ordinary wrench, I use socketed set screws for securing the collar to the shaft."
3

Set the parts up on a bar

Use plain steel washers and nuts, not zinc-plated ones. Wire-brush them clean. Grip a 16 mm round bar upright in the vice. Slide one washer onto it, stand four M8 nuts on the washer round the bar at quarter turns, each with a flat down and its hole pointing at the bar's centre and its inner face against the bar. Put the second washer on top and squeeze the stack with the C-clamp; check with the square that the washers are parallel.

Матеріали для цього кроку:

Плоска шайбаПлоска шайба2 штук
Шестигранна гайкаШестигранна гайка4 штук

Необхідні інструменти ({count})

Круглий пруток з маловуглецевої сталіКруглий пруток з маловуглецевої сталі
Слюсарні лещатаСлюсарні лещата
Струбцина типу CСтрубцина типу C
Набір дротяних щітокНабір дротяних щіток
Комбінований кутникКомбінований кутник
Цифровий штангенциркуль 6 дюймівЦифровий штангенциркуль 6 дюймів
4

Weld the nuts to the washers

Wearing the helmet and gloves, tack each nut to both washers with a short fillet weld at its outer corner, keeping the arc away from the bar. Let it cool, lift the collar off the bar, and run a fillet along both ends of every nut on both washers. Chip and wire-brush the slag. Run the set screw in and out of one nut to clear any spatter from its thread, and file the bore ends smooth.

Матеріали для цього кроку:

Зварювальний електродЗварювальний електрод4 штук

Необхідні інструменти ({count})

Апарат дугового зварюванняАпарат дугового зварювання
Зварювальна маска з автозатемненнямЗварювальна маска з автозатемненням
Зварювальні рукавиціЗварювальні рукавиці
Набір дротяних щітокНабір дротяних щіток
Кутова шліфмашинаКутова шліфмашина
Набір напилківНабір напилків
Захисні окуляриЗахисні окуляри
5

The collar in 3D

FreeCAD model, our sizes: the two 50 mm washers, the four M8 nuts between them at quarter turns, their inner faces on a 16 mm shaft, and the socket set screw in one nut. The welds are not modelled.
Файл дизайнуSTLCC0 - Free
6

Fit it on the shaft

Run an M8 x 8 cup point socket set screw into one nut from outside. Slide the collar onto the shaft to its place and tighten the screw with the hex key between the washers. Try to slide and turn it; it must not move.

Матеріали для цього кроку:

Установчий гвинт із чашоподібним кінцемУстановчий гвинт із чашоподібним кінцем1 штука

Необхідні інструменти ({count})

Набір шестигранних ключівНабір шестигранних ключів
7

Troubleshooting

Built-up collar troubleshooting.

Flow

Loading...
8

History and honest limits

**Ferdinand H. Dalrymple** of Bedford, Ohio, US 2,163,315, dated 20 June 1939, filed 2 November 1937. He claimed "opposed spaced plane plates formed with coaxial bores for the reception of a shaft, transverse spaced internally-threaded blocks welded to the opposed faces of the plates and serving as the sole means for holding the plates in relatively fixed positions, and set screws engaging the blocks". His Figs. 8 and 9 use standard square nuts and socketed set screws; we use hex nuts, as his Figs. 1-5 allow "standard nuts". His patent also shows special blocks, flanged plates, three-plate and split forms; we build the simplest. He gives no sizes for this form; every size here is ours.

Матеріали

4

Необхідні інструменти

13

Файли дизайну

1

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...