Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Steel-Faced Hand Hammers and Sledges: Ball, Fuller, Wedge and Claw Panes, Eye on Two Oval Drifts (Edwinson, 1886)
Forge

Створено

Forge

14. листопад 2026NO
9
0
0
0
0

Steel-Faced Hand Hammers and Sledges: Ball, Fuller, Wedge and Claw Panes, Eye on Two Oval Drifts (Edwinson, 1886)

How smiths made hand hammers and sledges, from George Edwinson's smithing series (Amateur Work, 1886): solid steel, or an iron head with a steel face welded into a slit fork; the eye punched and shaped on two oval taper drifts so the wedged handle cannot work loose. Panes: ball, fuller, wedge and claw.
Просунутий
A day at the forge

Інструкції

1

His weights

Завантаження блокнота Jupyter…
2

Read Edwinson

"To make a steel hammer it is only necessary to get a bar of steel the required size, heat, upset, and forge to the selected size and shape."
3

Solid steel route

Heat a steel bar of the size needed, upset it and forge it to shape. Punch the hole for the handle and work it on a taper drift. Tool the hammer off smoothly at a red heat, then heat it and harden it in water.

Матеріали для цього кроку:

Тигельна стальТигельна сталь1 штука

Необхідні інструменти ({count})

Кувальне горноКувальне горно
КовадлоКовадло
КувалдаКувалда
Ковальські кліщіКовальські кліщі
Оправка для розширення отворуОправка для розширення отвору
Гартівна діжкаГартівна діжка
4

Steel-faced route: weld the face

Upset a stout iron bar if it is too thin. Slit one end hot with a hot chisel (his sett) into a fork. Forge a steel bar to a wedge that fits it. Bring the iron to a welding heat and the steel to its own (a separate fire if needed), roll the steel in calcined borax and weld. Reheat with the steel protected by welding mixture or sand, and finish the weld.

Матеріали для цього кроку:

Пруток кованого залізаПруток кованого заліза1 штука
Смуги пухирчастої сталіСмуги пухирчастої сталі1 штука
Порошок буриПорошок бури1 штука
ПісокПісок1 штука

Необхідні інструменти ({count})

Кувальне горноКувальне горно
Гаряче зубило (ковальська рубка)Гаряче зубило (ковальська рубка)
КовадлоКовадло
КувалдаКувалда
Ковальські кліщіКовальські кліщі
5

Shape the head

Cut off the steel, forge steel and iron up into the face. Fashion the head and pane, punch the handle hole and form it on a taper drift, cut the hammer off the bar and finish it held in crooked bit tongs. If both ends are to be steel, weld in both before cutting off. Panes: ball for riveting, fuller for spreading iron, wedge, or claw for drawing nails.

Необхідні інструменти ({count})

Кувальне горноКувальне горно
Оправка для розширення отворуОправка для розширення отвору
Гаряче зубило (ковальська рубка)Гаряче зубило (ковальська рубка)
КовадлоКовадло
МолотокМолоток
Ковальські кліщіКовальські кліщі
6

Shape the eye on two drifts

Use two oval taper drifts: one tapered all round to form the lower side of the eye, the other tapered only on its long sides for the upper part. The eye tapers from both sides across the head, but only from the lower side lengthwise. Round the edges on the underside.

Необхідні інструменти ({count})

Кувальне горноКувальне горно
Оправка для розширення отворуОправка для розширення отвору
КовадлоКовадло
МолотокМолоток
7

Sizes and sledges

Hand hammers usually weigh 1-2 lb (0.45-0.9 kg). Larger fuller or wedge pane hammers of 3-30 lb are sledges; one-handed sledges weigh 3-5 lb; heavier ones get stout ash handles 3-4 ft (0.9-1.2 m) long for two hands.

Необхідні інструменти ({count})

КовадлоКовадло
8

Hang the head

Drive the handle into the eye from below so its end is compressed and fits tight. Cut off the extra wood, split the end with a chisel and drive in a wedge of well-seasoned wood. If the eye tapers two ways, cross-slit and drive two wedges.

Матеріали для цього кроку:

Заготовка з ясенаЗаготовка з ясена1 штука
Дерев'яні клиниДерев'яні клини1 штука

Необхідні інструменти ({count})

СкобельСкобель
СтамескиСтамески
МолотокМолоток
9

Troubleshooting

Hammer troubleshooting.

Flow

Loading...
10

History and honest limits

From George Edwinson, "Smithing and Forging" (part X), **Amateur Work, Illustrated**, vol. VI (Ward, Lock & Co., 1886-87), pp. 211-214 (checked on the archive.org scan amateurworkillus06lond), pp. 212-214 and figs. 227-235. He gives no temper for the face; the metric figures and tools are ours.

Матеріали

7

Необхідні інструменти

10

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...