Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Electric Kettle: Immersion Heater with a Steam and Switch-On-Dry Cut-Out (Taylor, US 4,358,666)
Ed

Створено

Ed

9. листопад 2026FI
7
0
0
0
0

Electric Kettle: Immersion Heater with a Steam and Switch-On-Dry Cut-Out (Taylor, US 4,358,666)

An automatic electric kettle boils water with an immersion heater and switches itself off. J. C. Taylor (US 4,358,666, 1982) mounts one control on the heater's head: a bimetal disc touching the hot head cuts the power if the kettle is switched on dry, and a second bimetal disc in the steam trips an over-centre lever that cuts it when the water boils. In his kettle (Fig. 14) the steam leaves through a hole high in the wall and runs down a passage between the handle and the wall to the control. A knob resets it. Source: J. C. Taylor, US Patent 4,358,666 (filed 1980, granted 1982). Picture: its Fig. 14.
Просунутий
Unknown

Інструкції

1

Read Taylor

"The effect is that when the water boils, the lever 16 is tripped by the actuator 22 from its first to its second position, thus interrupting the supply of electricity to the heating element."
2

Fit the immersion heater

Make the kettle body with a spout, lid and handle, an opening low in the back wall for the heater head and a hole high in the wall under the handle for steam. Fix the immersion heater's head watertight in the low opening, with its element low in the kettle and its hot return brazed to the head so the head heats up if the element runs dry. Form a steam passage between the handle and the wall from the high hole down to the head. Body material, size and heater rating are not given.

Матеріали для цього кроку:

Невідомий металНевідомий метал1 kettle body
Нагрівальний елементНагрівальний елемент1 immersion heater

Необхідні інструменти ({count})

Пальник для паяння твердим припоємПальник для паяння твердим припоєм
Свердлильний верстатСвердлильний верстат
Набір сверделНабір свердел
Невідомий спосіб формуванняНевідомий спосіб формування
Невідомі розміриНевідомі розміри
3

Build the switch-on-dry unit

On the head mount a switch unit with three pins (line, neutral and earth) for the kettle lead's socket. Wire the line pin to one cold end of the element through a movable contact on a springy conductive strip and a fixed contact. Rivet the tongue of a snap-acting bimetal disc to a pillar so its body touches the head. Fit a sliding link that the disc pushes: at about 120 °C (Taylor: "say 120° C.") the disc snaps over and the link parts the contacts.

Матеріали для цього кроку:

Невідомий ізоляційний матеріалНевідомий ізоляційний матеріал1 switch unit body
Невідомий металНевідомий метал1 pins, contacts and strip
Біметалева пластинаБіметалева пластина1 dry-switch disc

Необхідні інструменти ({count})

Свердлильний верстатСвердлильний верстат
Набір сверделНабір свердел
4

Make the steam unit

Press a disc of sheet bimetal into a domed die, with a cut-out that leaves a tongue in the middle, so it snaps over when steam heats it. Mount it by its rim on a lever that rocks on two knife edges in notches of a body seated over the switch unit, held by two over-centre C-springs, with a shroud round the pins and a steam opening sealed by an O-ring. A finger of the lever passes through the sliding link; a knob on the lever comes out through the housing. The trip temperature and bimetal grade are not given.

Матеріали для цього кроку:

Біметалева пластинаБіметалева пластина1 steam disc
Невідомий ізоляційний матеріалНевідомий ізоляційний матеріал1 steam unit body and lever
ПружинаПружина2 C-springs
Ущільнювальне кільце круглого перерізуУщільнювальне кільце круглого перерізу1 штука

Необхідні інструменти ({count})

Невідомий спосіб формуванняНевідомий спосіб формування
5

Close up and use

Screw the outer housing over both units into the threaded pillars, the knob through its opening and the steam passage meeting the steam unit's channel. Fill, plug in the lead and press the knob down to close the contacts. When the water boils, steam reaches the disc, the lever snaps over and the power goes off; switched on dry, the head heats and the other disc cuts it and holds the lever off. Press the knob to reset.

Матеріали для цього кроку:

Невідомий ізоляційний матеріалНевідомий ізоляційний матеріал1 outer housing
Гнучкий шнур із вилкоюГнучкий шнур із вилкою1 kettle lead with socket

Матеріали

7

Необхідні інструменти

5

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...