Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Geared Crank-Frame Churn: A Frame Over an Ordinary Churn Gears a Hand Crank Up to Drive a Grated Dasher by Pitman
Buttercup

Створено

Buttercup

11. листопад 2026IE
5
0
0
0
0

Geared Crank-Frame Churn: A Frame Over an Ordinary Churn Gears a Hand Crank Up to Drive a Grated Dasher by Pitman

J. W. Evans of Forsyth, Georgia, received US 28,462, dated 29 May 1860, for a frame on legs that stands over an ordinary churn. A hand crank turns a cogged wheel and a pinion, whose crank works a pitman and a sliding sash; the dasher is held in the sash by a set screw, so it is put in or taken out in a moment, and makes several strokes to each turn of the handle. The dasher is a grated one. The patent gives no sizes; every size here is ours.
Середній
About 2 days, plus printing

Інструкції

1

Several strokes to one turn

Завантаження блокнота Jupyter…
2

More strokes than turns, three months before

Clement gets two strokes a turn from a toggle. Evans gears his crank up for four.
3

Read US 28,462

"The nature of my invention consists in providing a frame with suitable gearing to communicate a reciprocating motion to which the dasher of an ordinary churn can be attached or detached with facility, the whole forming a churn which can be worked to great advantage by a laborer by means of a crank."
4

Print the grated dasher h

Disc 200 mm across and 10 thick with seven slots 14 mm wide, a rim and a cross bar. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
5

Print the cogged wheel w

Spur gear, module 2.5, 48 teeth, 12 mm wide, with a hub; bored 16.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
6

Print the pinion p

Spur pinion, module 2.5, 12 teeth, 12 mm wide, with a hub; bored 16.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
7

Frame A and legs L

From pine lumber 40 x 80 mm cut two uprights 570 mm long and a top bar 380 long, and join them 300 mm apart inside. Rout a groove 12 x 42 mm down the inside of each upright for the sash. Stand the frame on two rails and four legs 400 tall, the rails across the bucket's place so the frame stands over it. Screw a hardwood strap 60 x 20 mm upright behind the frame's middle, with a cross piece near its foot, and bore it 16.6 mm for the shafts c and d, 75 mm apart, 400 and 475 mm above the frame's foot.

Матеріали для цього кроку:

Сосновий пиломатеріалСосновий пиломатеріал3 штук
Дошка з твердої деревиниДошка з твердої деревини1 штука
Столярний клейСтолярний клей1 штука
Шурупи по деревуШурупи по дереву30 штук

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
Ручний фрезерРучний фрезер
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір перових сверделНабір перових свердел
Струбцина з напрямноюСтрубцина з напрямною
Набір викрутокНабір викруток
РулеткаРулетка
8

Wheel w, pinion p, cranks k and d

Pass a 16 mm stainless shaft c through the upper hole with the wheel w on its front end and a hardwood crank k 140 mm long with a dowel handle on its back end. Pass a short 16 mm shaft through the lower hole with the pinion p meshing w, and in front of it a hardwood crank d with a 12 mm stainless pin 40 mm from the shaft. Hold both with collars.

Матеріали для цього кроку:

Пруток із нержавкої сталіПруток із нержавкої сталі2 штук
Дошка з твердої деревиниДошка з твердої деревини1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука
Столярний клейСтолярний клей1 штука
Shaft CollarShaft Collar4 штук
Філамент PETGФіламент PETG1 штука

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Слюсарні лещатаСлюсарні лещата
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Наждачний папірНаждачний папір
9

Pitman e, sash f and set screw i

Cut a hardwood pitman 20 x 10 mm with 12.6 mm holes 220 mm apart. Cut a hardwood sash 320 x 40 x 40 mm with tongues on its ends to slide in the grooves; bore it 22.6 mm through the middle for the dasher rod, slot its front for the pitman, and pin the pitman in the slot. Drill and tap a hole through the sash's back into the bore, or set a nut in it, and run in a short piece of threaded rod with a wing nut as the set screw i.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
ШплінтШплінт2 штук
Шпилька різьбоваШпилька різьбова1 штука
Шестигранна гайкаШестигранна гайка1 штука
Гайка-баранецьГайка-баранець1 штука

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
ЕлектролобзикЕлектролобзик
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір перових сверделНабір перових свердел
Ножівка по металуНожівка по металу
Розвідний ключРозвідний ключ
10

Dasher g with the grate h

Glue a 22 mm hardwood dowel 555 mm long into the printed grate's centre, and cut a 28 mm hole in the centre of the bucket's lid for it.

Матеріали для цього кроку:

Шканти з твердої деревиниШканти з твердої деревини1 штука
Столярний клейСтолярний клей1 штука
Відро на 20 літрівВідро на 20 літрів1 штука

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Набір перових сверделНабір перових свердел
Акумуляторний дрильАкумуляторний дриль
11

The build in 3D

FreeCAD model of this build, the bucket cut open: the frame on its legs, the wheel w and pinion p behind the crank d, the pitman and the sash in its grooves, the dasher held by the set screw, and the grated dasher near the bucket's floor.
Файл дизайнуBLENDCC0 - Free
12

Churn

Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket and put on the lid. Stand the frame over it, pass the dasher down through the sash into the bucket, set it so it just clears the floor at the bottom of the stroke and tighten the set screw. Turn the crank k steadily, timing it. When the butter comes, loosen the set screw and lift the dasher out, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки8 l
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
13

Troubleshooting

Geared crank-frame churn troubleshooting.

Flow

Loading...
14

History and honest limits

**J. W. Evans** of Forsyth, Monroe County, Georgia, US 28,462, 29 May 1860, "Churn". He did not claim churn dashers worked by a crank nor the grated dasher, "as they are old and well known", but the arrangement with the grated dasher, sash and set screw. His frame is arched and on curved legs, and his wheel and pinion are drawn face-toothed; ours are spur gears on a strap behind a straight frame. Every size is ours.

Матеріали

16

Необхідні інструменти

19

Файли дизайну

4

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...