Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
New Year Noisemaker: a Spun Box Whose Wooden Tongues Clack Over a Pinned Bobbin (Folkush, 1921)
Woody

Створено

Woody

13. листопад 2026NO
8
0
0
0
0

New Year Noisemaker: a Spun Box Whose Wooden Tongues Clack Over a Pinned Bobbin (Folkush, 1921)

Martin Folkush of Milwaukee received US 1,374,644, dated 12 April 1921, for a noisemaker "that can be heard for a great distance". Hold the handle and swing the box round it: two thin wooden tongues inside snap over the posts of a fixed bobbin, one in single clacks and one in double, and the box rings like a sounding board. A slider changes the pitch. We make it from plywood, dowel and hardwood strip. All sizes are ours.
Середній
About 4 hours

Інструкції

1

Posts on the bobbin

Завантаження блокнота Jupyter…
2

Read US 1,374,644

"Upon rotating the casing 12 upon the shaft 11, the sounding boards 21 and 22 will be brought into violent engagement with the posts 19 and 20 causing loud sounds to be emitted."
3

Make the handle and shaft

Shape a handle from hardwood handle stock with a rasp, his handle 10, and glue a dowel shaft 11 into its end.

Матеріали для цього кроку:

Заготовка держака з твердої деревиниЗаготовка держака з твердої деревини1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука
Столярний клейСтолярний клей1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Рашпіль по деревуРашпіль по дереву
Наждачний папірНаждачний папір
Ручний дрильРучний дриль
4

Make the bobbin

Cut three plywood disks 60 mm across (ours): two ends and the middle disk 18. Drill all three on the circle from the notebook and glue dowel posts 19 through all of them; then glue the shorter posts 20 between the middle disk and one end disk only, between the long ones. Drill the centre for the shaft and pin the bobbin to it, his pin 17.

Матеріали для цього кроку:

Лист фанериЛист фанери1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука
Столярний клейСтолярний клей1 штука
ЦвяхиЦвяхи1 штука

Необхідні інструменти ({count})

Лобзикова пилкаЛобзикова пилка
Розмічальний циркульРозмічальний циркуль
Ручний дрильРучний дриль
Ручна пилкаРучна пилка
5

Make the casing

Cut two plywood sides 14 with a round head 13 at one end, bored for the shaft. Join them with a closed end 24 and an open frame so the bobbin turns freely between the heads. Glue a cross rib 23 inside the closed end. Cut a slot 28 in each side for the slider.

Матеріали для цього кроку:

Лист фанериЛист фанери1 штука
Столярний клейСтолярний клей1 штука
ЦвяхиЦвяхи1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Лобзикова пилкаЛобзикова пилка
Ручний дрильРучний дриль
6

Fit the sounding boards

Cut two thin hardwood strips (his sounding boards 21 and 22) long enough to reach from the rib to just inside the circle of posts, and screw their ends to the rib, side by side, one opposite each half of the bobbin.

Матеріали для цього кроку:

Смуга твердої деревиниСмуга твердої деревини1 штука
Шурупи по деревуШурупи по дереву1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Ручний дрильРучний дриль
Набір викрутокНабір викруток
7

Fit the slider and close the box

Make a small wooden slider 26 that surrounds both boards, with a length of threaded rod through it whose ends pass out through the slots; put a wing nut on each end (his set nuts 29). Put the casing on the shaft over the bobbin and close the other side with a plywood plate 25, making a resonant box.

Матеріали для цього кроку:

Смуга твердої деревиниСмуга твердої деревини1 штука
Шпилька різьбоваШпилька різьбова1 штука
Гайка-баранецьГайка-баранець2 штук
Лист фанериЛист фанери1 штука
Столярний клейСтолярний клей1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Ручний дрильРучний дриль
Ножівка по металуНожівка по металу
8

Play it

Hold the handle and swing the box round the shaft: the boards snap over the posts. Slide the slider toward the bobbin for a higher, sharper sound, away for a deeper one, and lock it with the wing nuts.
9

Troubleshooting

Noisemaker troubleshooting.

Flow

Loading...
10

History and honest limits

**Martin Folkush** of Milwaukee, US 1,374,644, dated 12 April 1921, filed 10 April 1920. He claimed "a noise maker comprising a shaft, a casing journaled thereon, a frame having spaced end supported posts", "one half of said frame being provided with double the number of posts that the other half has", and the pitch-adjusting slider. He names no materials and gives no sizes: the wood, all sizes, wing nuts and threaded rod are ours.

Матеріали

9

Необхідні інструменти

8

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...