Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО

Gasholder: Water-Sealed Zinc Gasometer with Balance Weights (Ramsay & Travers, 1898)
The laboratory gasometer Ramsay and Travers used to store argon: a zinc bell that rises and falls in a narrow ring of water between two fixed zinc cylinders. Because the water space is only about 2 cm wide, little gas dissolves in it. Weights on cords over pulleys balance the bell, and weights laid on top push the gas out.
Result: a water-sealed gasholder of 18 to 180 litres.
Source: M. W. Travers, The Experimental Study of Gases (1901), pp. 30 and 105-106. Unknown: sizes and how the zinc is joined. Picture: Fig. 34, the small mercury form of the same design.
Середній
Unknown
Інструкції
1
1
Make the fixed cylinders
Make the fixed cylinders
Make two concentric zinc cylinders on a closed base, leaving a ring-shaped space about 2 cm wide between them for the water. Make the top of the inner cylinder dome-shaped. Bring a gas pipe with a stopcock up through the inner cylinder. Ours: zinc soldered with tin-lead solder. Not given: sizes, how the zinc is joined, the stopcock.
Матеріали для цього кроку:
Цинковий лист1 outer and inner cylinders, base
Олов'яно-свинцевий припій1 seams
Невідомий вентиль1 gas stopcockНеобхідні інструменти ({count})
Ножиці по металу
Паяльник
Невідомий спосіб формування
Невідомі розміри2
2
Make and hang the bell
Make and hang the bell
Make the gasholder bell of zinc to fit closely over the inner cylinder and down into the water ring, with a dome-shaped top matching the inner cylinder's, so all the gas can be pushed out. Ramsay and Travers made bells of about 180, 27, 18 and 18 litres. Tie a cord to the top of the bell and pass it over pulleys to a hanging weight, to take the bell's own weight off the gas. Fill the ring with water. To deliver gas, take weight off the cord or lay weights on top of the bell. Not given: the weights.
Матеріали для цього кроку:
Цинковий лист1 bell
Олов'яно-свинцевий припій1 seams
Конопляний шпагат1 balance cords
Блок2 pulleys
Невідомий метал1 balance weightsНеобхідні інструменти ({count})
Ножиці по металу
ПаяльникМатеріали
6- 1 bellЗаповнювач
- 2 seamsЗаповнювач
- 1 gas stopcockЗаповнювач
- 1 balance cordsЗаповнювач
- 2 pulleysЗаповнювач
- 1 balance weightsЗаповнювач
Матеріали з пов'язаних креслень
За цим кресленням виготовляють
CC0 Суспільне надбання
Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.
Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.



