Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Half-Round Taper Reamer: Tool Steel Turned to the Taper, Filed Flat to the Centre Line, Hardened (Griswold, Amateur Work, 1905)
Forge

Створено

Forge

14. листопад 2026NO
9
0
0
0
0

Half-Round Taper Reamer: Tool Steel Turned to the Taper, Filed Flat to the Centre Line, Hardened (Griswold, Amateur Work, 1905)

The simplest home-made taper reamer, from Robert Gibson Griswold's Tool Making for Amateurs (Boston, 1905): tool steel turned to the taper wanted (his was 1/8 in. per foot), one side filed away exactly to the centre line so that two cutting edges remain, then hardened and ground on the flat face only. It reams a very smooth conical hole.
Середній
Two to three hours

Інструкції

1

His taper

Завантаження блокнота Jupyter…
2

Read Griswold

"Turn a piece of tool steel to the proper taper and then file away one side until the flat surface coincides with the center line."
3

Turn the taper

Turn a piece of tool steel in the lathe to the taper of the part the hole must fit (his: 1/8 in. per foot). Length and diameter are ours: a little longer than the hole and spanning its two diameters.

Матеріали для цього кроку:

Пруток інструментальної сталіПруток інструментальної сталі1 штука

Необхідні інструменти ({count})

Токарний верстат по металуТокарний верстат по металу
ШтангенциркульШтангенциркуль
4

File to the centre line

Hold it in the vice and file away one side until the flat face lies exactly on the centre line. This leaves a cutting edge on each side.

Необхідні інструменти ({count})

Слюсарні лещатаСлюсарні лещата
Напилки (ручний напилок)Напилки (ручний напилок)
ШтангенциркульШтангенциркуль
5

Harden and grind

Harden it (ours: heat to a cherry red and quench in water, temper to a straw colour), then grind on the flat side only, never on the round.

Необхідні інструменти ({count})

Кувальне горноКувальне горно
Гартівна діжкаГартівна діжка
Настільний точильний станокНастільний точильний станок
6

Troubleshooting

Reamer troubleshooting.

Flow

Loading...
7

History and honest limits

From Robert Gibson Griswold, "Tool Making for Amateurs" VII, **Amateur Work** (Boston), vol. IV (1904-05), p. 128 (checked on the archive.org scan amateurwork04bostrich). He gives no size or temper for the reamer; those and the tools are ours. He finishes the hardened bushings with a copper lap and emery.

Матеріали

1

Необхідні інструменти

7

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...