Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Four-Crank Gyrating Churn: Four Cranks Carry the Tub Round a Small Circle With No Dasher
Martin

Створено

Martin

10. листопад 2026NO
8
0
0
0
0

Four-Crank Gyrating Churn: Four Cranks Carry the Tub Round a Small Circle With No Dasher

Alfred Guthrie of Chicago received US 24,907, dated 26 July 1859, for a churn with no dasher at all. Four upright shafts in a frame have cranks on their tops, and a bed plate lies over the four crank pins, so each crank turns on its own centre but all move together. The tub stands on the plate, held by stirrups, and is carried round a small circle, throwing the cream against its sides. A handle turns one crank shaft through cogged gearing. This rung builds it at the patent's own sizes: a frame about two feet square and one foot high, shafts of 3/4 inch iron and 3 inch cranks.
Середній
About 2 days, plus printing

Інструкції

1

How hard the cream is swung

Завантаження блокнота Jupyter…
2

A churn with a dasher, before it

Wineman's dasher drove the cream through holes. Guthrie did away with the dasher and moved the whole tub.
3

Read US 24,907

"I connect the whole together by the bed plate D over the wrists of each crank E, E, E, E. Each crank will revolve upon its own center but will each correspond to the motion of the other."
4

Print the wheel H

The 64-tooth spur wheel (module 3, 198 mm across) for the handle shaft I, with a 20 mm bore. PETG, 0.2 mm layers, 50 % infill, 5 walls.
Файл дизайнуSTLCC0 - Free
5

Print the pinion H

The 24-tooth spur pinion for the driven crank shaft, with a 19 mm bore and a hub. PETG, 0.2 mm layers, 50 % infill, 5 walls.
Файл дизайнуSTLCC0 - Free
6

Frame and bearing bars

Build a pine frame 610 mm square and 305 mm high: four 50 mm corner posts, and 50 mm rails round the top and the bottom. Fit two hardwood bars across it, top and bottom, 150 mm in front of and behind the middle, and bore them 19.6 mm square to the frame at 200 mm either side of the middle, for the four shafts. Screw two hardwood brackets to the right side, top and bottom, bored 20.6 mm 132 mm out from the front right shaft, for the handle shaft.

Матеріали для цього кроку:

Соснова дошкаСоснова дошка2 штук
Хвойний брус 70x70 ммХвойний брус 70x70 мм2 штук
Дошка з твердої деревиниДошка з твердої деревини2 штук
Шуруп по дереву № 10 x 3"Шуруп по дереву № 10 x 3"24 штук
Столярний клейСтолярний клей1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Акумуляторний дрильАкумуляторний дриль
Набір перових сверделНабір перових свердел
Столярний косинецьСтолярний косинець
Будівельний рівеньБудівельний рівень
РулеткаРулетка
7

Shafts, cranks and plate D

Cut four 19 mm steel shafts 323 mm long and stand them in the bars. Make four hardwood crank arms, 76 mm from the shaft to the crank pin, and pin them on the shafts' tops all pointing the same way. Fit a 19 mm steel crank pin 50 mm long in each. Cut plate D 532 mm across from plywood, bore it for the four pins exactly where they stand, and drop it on them. Turn one crank by hand: the plate must run round freely without turning.

Матеріали для цього кроку:

Сталевий пруток-заготовкаСталевий пруток-заготовка2 штук
Дошка з твердої деревиниДошка з твердої деревини1 штука
Лист фанериЛист фанери1 штука
Плоска шайбаПлоска шайба8 штук
Набір шестигранних болтівНабір шестигранних болтів4 штук
Самоконтрувальна гайка з нейлоновим кільцемСамоконтрувальна гайка з нейлоновим кільцем4 штук
Столярний клейСтолярний клей1 штука

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Слюсарні лещатаСлюсарні лещата
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
ЕлектролобзикЕлектролобзик
РулеткаРулетка
Розвідний ключРозвідний ключ
8

Gearing H and handle I

Pin the pinion on the front right shaft 140 mm up. Stand a 20 mm steel shaft 885 mm long in the brackets, pin the wheel on it level with the pinion, and check they mesh fully. Fix a hardwood handle arm 150 mm long on the shaft's top with a dowel grip.

Матеріали для цього кроку:

Філамент PETGФіламент PETG1 штука
Сталевий пруток-заготовкаСталевий пруток-заготовка1 штука
Дошка з твердої деревиниДошка з твердої деревини1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука
Столярний клейСтолярний клей1 штука

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
Ножівка по металуНожівка по металу
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
9

Tub F on its grooved bottom

Glue a plywood ring to the plate's middle, 282 mm inside and 340 mm outside, so the bucket's foot sits in it. Bend two flat-bar stirrups to go up the bucket's sides and over its lid, notch the ring for them and bolt them to the plate.

Матеріали для цього кроку:

Лист фанериЛист фанери1 штука
Столярний клейСтолярний клей1 штука
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі2 штук
Набір шестигранних болтівНабір шестигранних болтів4 штук
Самоконтрувальна гайка з нейлоновим кільцемСамоконтрувальна гайка з нейлоновим кільцем4 штук
Відро на 20 літрівВідро на 20 літрів1 штука

Необхідні інструменти ({count})

ЕлектролобзикЕлектролобзик
Слюсарні лещатаСлюсарні лещата
Ножівка по металуНожівка по металу
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Розвідний ключРозвідний ключ
10

The build in 3D

FreeCAD model of this build: the frame with its bearing bars, the four shafts and cranks, plate D on the crank pins, the bucket in its ring under two stirrups, and the spur wheel on the handle shaft driving the pinion. It was checked at eight crank angles.
Файл дизайнуBLENDCC0 - Free
11

Churn

Pour about 8 litres of heavy cream at about 15 °C into the bucket, checked with the thermometer, put the lid on and tighten the stirrups. Turn the handle steadily and time it. When the butter comes, lift the bucket off, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки8 l
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
12

Troubleshooting

Four-crank churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Alfred Guthrie** of Chicago, Illinois, assignor to Wardell Guthrie, US 24,907, 26 July 1859, "Churn". He claimed the cranks C connected by the plate D. His sizes are kept: a frame about two feet square and one foot high, shafts of 3/4 inch iron about a foot long, and cranks of 3 inches, which we read from "about a six inch throw or three inches" and Fig. 3's "3 in" marks. He gives no gear sizes; ours are printed spur gears placed as his Figs. 2-3 draw them. Every other size is ours.

Матеріали

17

Необхідні інструменти

17

Файли дизайну

3

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...