Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Hackle Combs: Coarse and Fine Flax Heckles on One Board (Ure, 1839)
Woody

Створено

Woody

4. листопад 2026NO
12
0
0
0
0

Hackle Combs: Coarse and Fine Flax Heckles on One Board (Ure, 1839)

A pair of flax heckles on one oblong plank: two round wooden blocks, each faced with a drilled brass or iron plate holding upright iron teeth. Flax is drawn first through the coarse heckle, then through the fine one, splitting the fibres, combing out the short tow and laying the long fibres straight. Coarse: teeth about 1/10 in thick and 1 1/4 in long, a centre tooth and 12 rings, the outer ring 5 3/4 in across. Fine: thinner teeth set closer, 1109 of them. Source: Andrew Ure, Dictionary of Arts, Manufactures and Mines (1839), 'Flax'. Picture: Figs. 424-425 of the book.
Середній
Unknown

Інструкції

1

Make the board and blocks

Cut an oblong plank (Fig. 424, a b) and two round (or square) wooden blocks, c for the coarse heckle and d for the fine, and fix the blocks on the plank (Fig. 425). The heckles can also be made on separate boards.

Матеріали для цього кроку:

Дошка твердої деревиниДошка твердої деревини1 штука
Брусок твердої деревиниБрусок твердої деревини2 штук
Шурупи по деревуШурупи по дереву1 штука

Необхідні інструменти ({count})

Обушкова пилкаОбушкова пилка
Викрутка пласкаВикрутка пласка
2

Drill the face plates

Cover the top of each block with a brass or iron plate drilled for the teeth, which gives them a firmer hold. Set the holes evenly over the whole face, in concentric circles (the German way) or parallel rows (the English way). Coarse: a centre hole and 12 rings, the outermost 5 3/4 in across. Fine: thinner holes set closer, 1109 in all.

Матеріали для цього кроку:

Латунний листЛатунний лист2 face plates

Необхідні інструменти ({count})

Розмічальний циркульРозмічальний циркуль
Ножиці по металуНожиці по металу
Ручний дрильРучний дриль
3

Make the teeth

Cut teeth of iron (sometimes steel) 1 to 2 in long. For the coarse heckle make them about 1/10 in thick and 1 1/4 in long, tapering from the middle to a very fine point; the fine heckle's teeth are thinner. File every point sharp and smooth, running evenly into the round stem like a sewing needle; square points in a rhombus shape cut the fibres apart better than round ones.

Матеріали для цього кроку:

Залізний дрітЗалізний дріт1 teeth

Необхідні інструменти ({count})

Ножиці по металуНожиці по металу
Напилок по металуНапилок по металу
4

Set the teeth

Drive each tooth through its hole in the plate into the block so it stands upright, all points at one level.

Необхідні інструменти ({count})

МолотокМолоток

Матеріали

5

Необхідні інструменти

7

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...