Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Screw Auger: a Steel Blade Twisted Red-Hot, with a Worm, Two Lips and an Eye for the Cross Handle (Holtzapffel, 1846)
Forge

Створено

Forge

14. листопад 2026NO
10
0
0
0
0

Screw Auger: a Steel Blade Twisted Red-Hot, with a Worm, Two Lips and an Eye for the Cross Handle (Holtzapffel, 1846)

How the common English screw auger was made, from Holtzapffel's Turning and Mechanical Manipulation: a parallel steel blade twisted red-hot, a worm at the point to pull it into the wood, two lips sharpened to cut, and the shaft end forged into an eye for a tightly driven cross handle.
Просунутий
A day at the forge

Інструкції

1

Twist count

Завантаження блокнота Jupyter…
2

Read Holtzapffel

"The ordinary screw auger ... is forged as a parallel blade of steel ... it is twisted red-hot."
3

Forge the blade

Draw a steel bar out into a flat, parallel blade, leaving a round end for the shaft. Width, thickness and length are ours: make the blade as wide as the hole you want.

Матеріали для цього кроку:

Пруток інструментальної сталіПруток інструментальної сталі1 штука

Необхідні інструменти ({count})

Кувальне горноКувальне горно
КовадлоКовадло
МолотокМолоток
Ковальські кліщіКовальські кліщі
Фулер (прутик для канавок)Фулер (прутик для канавок)
4

Twist it red-hot

Heat the blade to red, grip one end in the vice and twist the other with a wrench into an even double spiral. Twist in short heats and keep the pitch even.

Необхідні інструменти ({count})

Кувальне горноКувальне горно
Слюсарні лещатаСлюсарні лещата
Коловорот для мітчиківКоловорот для мітчиків
Ковальські кліщіКовальські кліщі
5

Form the worm and lips

File the point into a worm (a small tapered screw, as on a gimlet) that pulls the auger into the work. Shape and sharpen the two corners, or lips, to cut at the very ends and a little up the sides.

Необхідні інструменти ({count})

Слюсарні лещатаСлюсарні лещата
Напилки (ручний напилок)Напилки (ручний напилок)
6

Forge the eye

Forge the top of the shaft into a ring or eye.

Необхідні інструменти ({count})

Кувальне горноКувальне горно
КовадлоКовадло
МолотокМолоток
Ковальські кліщіКовальські кліщі
7

Harden and temper (ours)

He gives no hardening. Ours: harden the cutting end and temper it as for other wood-cutting edge tools, then hone the lips.

Необхідні інструменти ({count})

Кувальне горноКувальне горно
Гартівна діжкаГартівна діжка
Точильний брусокТочильний брусок
8

Fit the cross handle

Shape a hardwood bar and drive it tightly through the eye as a transverse handle.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука

Необхідні інструменти ({count})

СкобельСкобель
МолотокМолоток
9

Troubleshooting

Screw auger troubleshooting.

Flow

Loading...
10

History and honest limits

From Charles Holtzapffel, **Turning and Mechanical Manipulation**, vol. II (1846), pp. 540, 543 and 545-546 (checked on the archive.org scan turningmechanica02holtuoft). He also describes the single-lip auger: a half-round bar coiled into an open spiral with the flat side outwards, the end shaped like a shell auger. He gives no sizes or heat treatment: those, the tools and the handle wood are ours.

Матеріали

2

Необхідні інструменти

11

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...