Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Hot Plate Magnetic Stirrer: Ring Heater over a Relay Magnet on a Shielded Spindle (Hug, US 3,028,476)
Ed

Створено

Ed

9. листопад 2026FI
10
0
0
0
0

Hot Plate Magnetic Stirrer: Ring Heater over a Relay Magnet on a Shielded Spindle (Hug, US 3,028,476)

A laboratory stand that heats a vessel and stirs it at the same time. A motor in the base spins a bar magnet; in Theodore Hug's design (US 3,028,476, 1962) that magnet turns a second, free bar magnet on a spindle inside the hot plate, which in turn spins a coated stirring bar in the vessel. A stainless-steel radiation shield and an air gap keep the ring heater's heat away from the motor. The relay magnet sits about 1/2 in. under the aluminium heat sink: closer, eddy currents in the sink slow the stirring. Source: T. Hug, "Hot Plate and Magnetic Stirrer", US Patent 3,028,476 (filed 1960, granted 1962). Picture: its Figs. 1-2.
Просунутий
Unknown

Інструкції

1

Read Hug

"Attempts have been made to couple conventional heating means to magnetic stirrers, but the same have proved to be unsuccessful. Thus, the base of a laboratory vessel must be positioned relatively close to the driving rotating magnet ... Moreover, if an appreciable amount of heat from the heating means is transmitted to the motor of the magnetic stirrer, it will drastically reduce the useful operating life of said motor."
2

Build the stirrer base

Make a housing of aluminium (or another non-magnetic material) and mount an electric motor inside with its shaft upright. Fix a permanent bar magnet horizontally on the top of the shaft, just under the housing top. Wire the motor through a rheostat to its cord so the speed can be varied. Sizes, motor rating and how the housing is formed are not given.

Матеріали для цього кроку:

Алюмінієвий листАлюмінієвий лист1 housing
ЕлектродвигунЕлектродвигун1 штука
Набір смугових магнітівНабір смугових магнітів1 drive magnet
РеостатРеостат1 штука
Гнучкий шнур із вилкоюГнучкий шнур із вилкою1 штука

Необхідні інструменти ({count})

Невідомі розміриНевідомі розміри
Невідомий спосіб формуванняНевідомий спосіб формування
3

Make the radiation shield

Shape a radiation shield of non-magnetic stainless steel so it straddles the top of the housing, on stainless-steel legs (a poor conductor of heat) that stand on the housing top. Bore its centre and fit a threaded spindle there with a nut on each side of the shield. Tap a blind thread in each leg.

Матеріали для цього кроку:

Лист нержавкої сталі - 304Лист нержавкої сталі - 3041 shield and legs
Шпилька різьбоваШпилька різьбова1 spindle
Шестигранна гайкаШестигранна гайка2 штук

Необхідні інструменти ({count})

Ножиці по металуНожиці по металу
Свердлильний верстатСвердлильний верстат
Набір сверделНабір свердел
Набір мітчиків і плашокНабір мітчиків і плашок
Невідомий спосіб формуванняНевідомий спосіб формування
4

Fit the relay magnet

Bore a blind cavity in a hub of non-magnetic material so it turns freely on the spindle. Lay a permanent bar magnet 1/4 in. by 1 in. by 1 3/4 in. on top of the hub and hold it with a strap screwed to the hub. The hub and strap material is not given.

Матеріали для цього кроку:

Набір смугових магнітівНабір смугових магнітів1 relay magnet, 1/4 x 1 x 1 3/4 in.
Невідомий матеріалНевідомий матеріал1 hub and strap
Машинні гвинтиМашинні гвинти2 штук

Необхідні інструменти ({count})

Токарний верстат по металуТокарний верстат по металу
Свердлильний верстатСвердлильний верстат
Набір сверделНабір свердел
Набір мітчиків і плашокНабір мітчиків і плашок
5

Mount the supports

Make three support members of non-magnetic stainless steel, each an upright with flanges. Screw the flanges down into the legs, with small tubular spacers of insulating material round the screws between the shield and the flanges, so air can circulate and carry heat away. Fit a grommet in one support for the heater cord. The spacer material is not given.

Матеріали для цього кроку:

Лист нержавкої сталі - 304Лист нержавкої сталі - 3041 three supports
Машинні гвинтиМашинні гвинти3 штук
Невідомий ізоляційний матеріалНевідомий ізоляційний матеріал3 tubular spacers

Необхідні інструменти ({count})

Ножиці по металуНожиці по металу
Свердлильний верстатСвердлильний верстат
Набір сверделНабір свердел
6

Fit the heater and top

Mount an annular ring heater (elements in a non-magnetic sheath) coaxial with the spindle; join its cord wires to its threaded stud between two nuts. Above it lay an aluminium heat sink, a flat plate wider than the heater, so the relay magnet is about 1/2 in. below it. Cover with a top plate of aluminium or stainless steel whose edge is spun into an inverted dish, and screw the edge to the tops of the supports. The patent claims a blackened outer surface on the heat sink and top plate (how is not given). In use, set the hot plate on the stirrer and put a stirring bar (a short bar magnet sealed in glass or coated with PTFE) in the vessel: the drive magnet turns the relay magnet, which turns the bar.

Матеріали для цього кроку:

Нагрівальний елементНагрівальний елемент1 ring heater
Гнучкий шнур із вилкоюГнучкий шнур із вилкою1 штука
Шестигранна гайкаШестигранна гайка2 штук
Алюмінієва пластинаАлюмінієва пластина1 heat sink
Алюмінієвий листАлюмінієвий лист1 top plate
Машинні гвинтиМашинні гвинти3 штук

Необхідні інструменти ({count})

Інструмент для давильних робітІнструмент для давильних робіт
Токарний верстат по металуТокарний верстат по металу
Свердлильний верстатСвердлильний верстат
Набір сверделНабір свердел

Матеріали

13

Необхідні інструменти

8

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...