Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Water-and-Air Tube Churn: Two Tubes of Warm or Cold Water and an Open Air Tube Stand by the Wall, Blades Sweep Under and Between
Buttercup

Створено

Buttercup

12. листопад 2026IE
8
0
0
0
0

Water-and-Air Tube Churn: Two Tubes of Warm or Cold Water and an Open Air Tube Stand by the Wall, Blades Sweep Under and Between

Thomas A. Jebb of Buffalo, New York, received US 32,697, dated 2 July 1861, for a geared churn with three tubes standing just inside its wall. Two are closed at the bottom and filled with cold water or ice in summer, warm water in winter, to bring the cream to the right warmth; the third is open at both ends, and the long lower dash blade, sweeping under its foot, draws air down it into the cream. The tubes also split the swirling cream, part through the gap by the wall and part back toward the shaft. Funnels in the cover feed the tubes without lifting it. The gap between the tubes and the wall is the patent's; every other size here is ours.
Середній
About 2 days

Інструкції

1

Tempering the cream from inside

Завантаження блокнота Jupyter…
2

Jebb's earlier churn, a year and a half before

In his first churn Jebb split the current with thick staves and swept a long blade beneath them. Here tubes do the splitting, and also temper and air the cream.
3

Read US 32,697

"The nature of this invention relates to the application and use of three tubes (A, A,) and (B) so arranged within the churn as to serve the threefold purpose of, 1st, breaking and dividing the body of cream, as it is set in motion by the dash blades, 2d, graduating the temperature of the cream by the use of warm or cold water in the tubes (A, A,) and 3d, ventilating, by causing a current of air to pass down the tube (B,) into the midst of the cream."
4

Print the tube plugs (two)

A plug sealing the bottom of a water tube: 37.6 mm across, 15 long, with a 42 mm lip. Print two; seal them in with silicone. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
5

Print the rings C (six)

A ring round a tube: 50 mm across, 40.2 bore, 12 high, with a boss and a 5.2 mm hole for the shank. Print six. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
6

Tubes A, A and B, rings C, shanks d and nuts e

Use a 20-litre food-grade bucket as the churn. Cut three 40 mm stainless tubes 315 mm long. Seal a printed plug into the bottom of two of them, the water tubes A; leave the third, the air tube B, open at both ends. Stand them a third of a turn apart round the inside, 40 mm off the floor, their outsides 15 mm from the wall all the way up (the patent's half to three quarters of an inch), leaning with the wall. Put two rings C on each, 110 and 280 mm up, run an M6 threaded rod shank d from each ring out through a hole in the wall, and tighten a nut e and washer on it outside, sealed with silicone.

Матеріали для цього кроку:

Відро на 20 літрівВідро на 20 літрів1 штука
Труба з нержавкої сталіТруба з нержавкої сталі1 штука
Філамент PETGФіламент PETG1 штука
Силіконовий герметикСиліконовий герметик1 штука
Шпилька різьбоваШпилька різьбова1 штука
Шестигранна гайкаШестигранна гайка12 штук
Плоска шайбаПлоска шайба12 штук

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Розвідний ключРозвідний ключ
РулеткаРулетка
7

Print the step

The step on the floor: 40 mm across, 12 high, with a 16.8 mm hole 8 deep. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
8

Shaft F and dash blades G

Cut a 16 mm stainless shaft 440 mm long. Mortise three hardwood dash blades G 24 x 8 mm through hardwood hubs on it: the lower 250 mm long, 20 mm above the floor, sweeping under the tubes' ends; the other two 140 mm long, at 150 and 260 mm, turned 60 and 120 degrees from it, sweeping between the tubes. Stand the shaft in the step.

Матеріали для цього кроку:

Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
Дошка з твердої деревиниДошка з твердої деревини1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука
Столярний клейСтолярний клей1 штука

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
Набір стамесок по деревуНабір стамесок по дереву
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Ножівка по металуНожівка по металу
9

Print the pinion H

The pinion on the shaft's top: 14 teeth, module 2.5, 16.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
10

Print the wheel I

The driving wheel: a crown wheel of 42 teeth, module 2.5, 16.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
11

Cover K, tunnels n, frame J, wheels H and I, winch M, hooks l

Cut a 12 mm HDPE cover K to the bucket's top, bored 16.8 mm at the centre and 21 mm over each tube's mouth. Set a small kitchen funnel in each of those holes, its spout reaching down into the tube, as the tunnels n. Pin the pinion H on the shaft 40 mm above the cover. Screw two hardwood blocks 50 x 25 x 118 mm, the frame J, to the cover 60 and 125 mm from the centre, bored 16.6 mm across 93 mm up; run a 16 mm stainless shaft 150 mm long through them with the wheel I pinned on meshing H, a shaft collar, and a winch M of mild steel flat bar, 100 mm throw, with a hardwood handle. Fix two hooks and eyes l to hold the cover to the bucket.

Матеріали для цього кроку:

Лист ПЕВГЛист ПЕВГ1 штука
Кухонна лійкаКухонна лійка3 штук
Дошка з твердої деревиниДошка з твердої деревини1 штука
Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
Shaft CollarShaft Collar1 штука
ШплінтШплінт3 штук
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука
Шурупи по деревуШурупи по дереву6 штук
Гачок і петляГачок і петля2 штук
Філамент PETGФіламент PETG1 штука

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
КомпасКомпас
ЕлектролобзикЕлектролобзик
Набір перових сверделНабір перових свердел
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Слюсарні лещатаСлюсарні лещата
Набір викрутокНабір викруток
12

The build in 3D

FreeCAD model of this build, the bucket cut open: the two closed water tubes and the open air tube on their rings and shanks, the shaft with the long lower blade under the tubes and two short blades between them, the cover with its funnels, and the gearing and winch.
Файл дизайнуBLENDCC0 - Free
13

Temper and churn

Pour about 10 litres of heavy cream into the bucket and hook on the cover. Pour cold water or ice water into the two water tubes through their funnels if the cream is warm, warm water if it is cold; each filling moves the cream only a degree or two, so start with cream near 15 °C, checked with the thermometer, and refill the tubes as it drifts. Leave the air tube's funnel open. Turn the winch steadily, timing it. When the butter comes, unhook and lift off the cover and gearing, lift out the shaft, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it. Empty the water tubes.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки10 l
ВодаВода1 штука
Крупна морська сільКрупна морська сіль1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
14

Troubleshooting

Tube churn troubleshooting.

Flow

Loading...
15

History and honest limits

**Thomas A. Jebb** of Buffalo, Erie County, New York, US 32,697, 2 July 1861, "Churn". He claimed "the described arrangement of the water tubes A, A, air tube B, and dash blades G, G, G within the churn tub, so that a space may be left between the said tubes and the sides of the churn tub, and so that the lower dash blade shall revolve under the lower ends of said tubes, while the other dash blades shall revolve in the space between said tubes". His text calls the shaft both F and E. His tub widened toward the bottom; ours, a bucket, widens toward the top, and our tubes lean with it. The gap of half to three quarters of an inch is his; every other size here is ours.

Матеріали

21

Необхідні інструменти

18

Файли дизайну

6

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...